Table of Contents
Advertisement
Use compact discs bearing the symbol shown. In
additional to conventional 12 cm CDs, this sys-
tem can be used to play 8 cm CDs without an
adaptor.
1. Press the buttons door (PUSH OPEN portion) to open buttons door.
2. Press the FUNCTION button to select "CD" function. "CD" appears
on the display, then "CD" is replaced by "NO DISC".
3. Push the buttons door back into position to close it.
4. Press the q OPEN/CLOSE button, the mirror door slide down, then
CD compartment is opened. "OPEN" appears.
5. Place the disc with the label
facing toward you on the disc
turntable. (Place only one disc
at a time.)
6. Press the q OPEN/CLOSE
button again, the mirror door
slide up, the CD compartment
is closed. The total number of
tracks and total playing time on the
disc appear.
NOTE:
If the disc is loaded with the label facing backward you, or if a badly
scratched disc is loaded. "NO DISC" appears. If this occurs, load the
disc correctly or replace the damaged disc.
7. Press the i button. " A " appears. Play starts from the first track.
The current track number and elapsed playing time are displayed.
8. Press the n button to end disc play.
When the last track has been played, the player stops automatically.
Note:
Always press the n button and wait for the disc to stop rotating before
opening the CD compartment.
Notes on handling compact discs
-
Do not expose the disc to direct sunlight, high humidity or high tem-
peratures for extended periods of time.
-
Discs should be returned to their cases after use.
-
Do not apply paper or write anything on the disc surface.
-
Handle the disc by its edge. Do not touch the playing surface (glossy
side).
-
Fingerprints and dust should be carefully wiped off the playing sur-
face of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
-
Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the e or f button, then press the i
button.
Temporarily stopping play
Press the i button. " A " and elapsed playing time blink on the display.
To resume play, press the button again.
Skip play
To skip to track 6 while track 3 is playing, press the e button repeat-
edly until "6" appears (in the track section) on the display. To skip back
to track 3 while track 6 is playing, press the f button repeatedly until
"3" appears.
Search (forward/reverse)
If the e button or the f button is pressed during play, the player
will search at high speed in the forward or reverse direction while the
button is being pressed. When the button is released, normal play will
continue.
CD PLAY
Mode function
Press the MODE button repeatedly before or during play to select a
various play mode available.
Each time the MODE button is pressed, the mode changes as shown
below :
REPEAT ALL appears
(Repeat all tracks)
Release
(Normal play mode)
NOTE:
"RANDOM" mode can not be selected during a programmed play.
PROGRAMMED PLAY
Up to 20 tracks on a disc can be programmed for play in any order.
-
First, select "CD" function and load a disc that you want to
programme.
-
The tracks must be programmed in the stop mode.
-
The same track can be programmed more than once.
1. Press the MEMORY button.
2. Select a track by using the e or f button.
3. Press the MEMORY button.
4. Repeat steps 2 - 3 to programme additional tracks.
5. Press the i button to start programmed play.
When all programmed tracks have played, the first programmed
track will appears and "MEMORY" will blink.
-
The programme contents are retained in memory.
-
The maximum number of selections that can be programmed is 20.
If you try to enter more selections. "MEMORY" and "FULL" blink on
the display.
-
The programme contents are retained even if the function selection
is changed.
-
To cancel programmed play, press the n button twice.
Checking the programme
Each time the MEMORY button is pressed in the stop mode, the pro-
grammed details sequentially appear on the display.
Changing a programme
To add a new track to a programme:
1. In the stop mode, press the MEMORY button repeatedly until "00"
(on the track section) appears on the display.
2. Select a track as explained above.
3. Press the MEMORY button.
To change a track:
1. In the stop mode, press the MEMORY button repeatedly until the
selection to be replaced is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
Note:
Programmed details cannot be partially deleted or inserted.
-7-
REPEAT appears
v
(Repeat one track)
RANDOM appears
(The tracks are played in
random order)
Hide quick links:
Advertisement
Table of Contents
