N-Tron 608MFX-ST Network Configuration Manual
600 series industrial ethernet switches
Hide thumbs
Also See for 608MFX-ST:
- Hardware installation manual (23 pages) ,
- Installation manual (22 pages) ,
- Specifications (2 pages)
Related Manuals for N-Tron 608MFX-ST
Summary of Contents for N-Tron 608MFX-ST
- Page 1 600 Series Industrial Ethernet Switches Network Configuration Guide...
- Page 2 Industrial Ethernet Switch Network Management Guide 608MFX-ST 608MFXE-ST-15 608MFXE-ST-40 608MFXE-ST-80...
- Page 3 In no event shall N-TRON Corp. be liable for any incidental, special, indirect, or consequential damages whatsoever included but not limited to lost profits arising out of errors or omissions in this manual or the information contained herein.
-
Page 4: Safety Warnings
Safety Warnings ELECTRICAL SAFETY WARNING: Disconnect the power cable before removing the enclosure top. WARNING: Do not operate the unit with the top cover removed. WARNING: Do not work on equipment or cables during periods of lightning activity. WARNING: Do not perform any services on the unit unless qualified to do WARNING: Do not block the air vents. - Page 5 608MFX NETWORK CONFIGURATION The N-TRON 608MFX is a product derivative of the OSM/ESM family jointly manufactured by Siemens and N-TRON. Some of the software menus may refer to the OSMTP62 (Optical Systems Module) or ESM (Electrical Systems Module) when identifying the N-TRON 608MFX. These names are synonymous.
- Page 6 Enter your administrator or user password and press [Return]. The CLI then displays the start menu and the prompt CLI> You can now activate the commands of the CLI. Reset You can reset the 608MFX by depressing and holding the Select/Set button. If necessary, depress the Select/Set button until the diplay mode LEDs indicate the port status (all diplay mode LEDs = OFF).
- Page 7 CLI Commands This section explains the commands of the CLI, their functions and syntax. The commands that are available depend on the access level; in other words, whether you logged in as user or as administrator. Table 3–2 contains an overview of the commands available for the administrator and user.
- Page 8 Example: The following example illustrates how to use CLI commands. The command status <E | D> [ports] is used to enable or disable 608MFX ports. The user enters the following: status followed by a blank and then the mandatory setting either E (= enable) or D (= disable) and then the optional port numbers as described in Table 3–1.
- Page 9 Table 3–2 Start Menu Commands - Continued Opens the Optical Systems You make the 608MFX– Module menu. specific settings (for example fault mask) in the OSM menu. AGENT Opens the AGENT menu. You can enter the settings for network management (for example IP address) in the agent menu.
- Page 10 Table 3-3 Settings in the System Menu – Continued memreset Restores the defaults of the Administrator command 608MFX. The device is restores the factory settings of automatically restarted. the 608MFX. With the exception of the ”protected settings”, the settings made by the user are reset to the default values.
- Page 11 Table 3-3 Settings in the System Menu – Cont. cfgname Enters the name (max. 32 characters) Administrator only <filename> under which the 608MFX configuration is loaded or stored as a file on the TFTP server. Depending on the configuration of the TFTP server, this may also include further path names.
- Page 12 Table 3–4 Settings in the OSM Menu - Continued power <E | D> [lines] Enable | Disable monitoring Administrator only of the power supply lines L1 Monitoring of the and L2. power supply lines L1 and L2 is part of the Example: fault mask of the power E 1,2 enables...
- Page 13 Table 3–4 Settings in the OSM Menu – Cont. resetc Resets the 608MFX Administrator only counters. observer <E | D | R> Enables, disables and Administrator only restarts the observer. The operating state of the observer can be read out with the info command.
- Page 14 Table 3–5 Settings in the Agent Menu - Continued from <address> Sets the “from” field (up to Administrator only 50 characters) of the E-mail Default function. OSM@ <IP-address> bootp <D | E> Disable | Enable BOOTP Administrator only Disable | Enable RMON Administrator only rmon <D | E>...
- Page 15 Table 3–5 Settings in the Agent Menu – Cont. ping [count] [size] <IP> Sends a ping to the Ten (count) pings with a frame specified IP address. length (size) of 128 bytes are Example: sent to IP address 192.168.1.1. ping -c 10 -s 128 192.168.1.1 showec Shows the current event...
- Page 16 Table 3–6, Settings in the Switch Menu - Continued aging <E | D> Enable | Disable aging. Administrator only When aging is activated, a land address is automatically deleted in the FDB table of the 608MFX if no packet is received from the station with the relevant MAC address within the aging time.
- Page 17 Table 3–6, Settings in the Switch Menu - Cont. flow <D | E> Enable | Disable the flow control Administrator only for all 608MFX ports find Finds a MAC address in the FDB The address must be < MAC address > table of the 608MFX.
- Page 18 Table 3–7 Settings in the Port Menu - Continued stat <S|T| E | clear> [port] Shows the counter readings - of the frame length (S) - of the frames (T) - of the errors (E) of the selected port. The counters are reset with clear. Examples: show S 1,3-5 Shows the frame length of ports 1...
- Page 19 Table 3–7 Settings in the Port Menu – Cont. hd_flow <E | D> [port] Enable | Disable half duplex Administrator only flow control. This flow control is effective when the selected ports operate in the half duplex mode and when flow control is activated in the Switch menu.
- Page 20 N-TRON Limited Warranty N-TRON, Corp. warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from N-TRON or its authorized reseller.
- Page 21 AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. N-TRON SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR...
- Page 22 allowed to be excluded in their entirety, they will be limited to the duration of the applicable written warranty. This warranty gives you specific legal rights which may vary depending on local law. GOVERNING LAW: This Limited Warranty shall be governed by the laws of the State of Alabama, U.S.A.