Related Manuals for Clarke CAT80
Summary of Contents for Clarke CAT80
- Page 1 6” DUAL-ACTION SANDER MODEL NO: CAT80 Part No: 3110800 OPERATION & MAINTENANCE INSTRUCTIONS GC06/13...
-
Page 2: Introduction
GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ................2 GUARANTEE ................2 ENVIRONMENTAL PROTECTION ..........2 TABLE OF CONTENTS ..............3 SAFETY PRECAUTIONS ..............4 OVERVIEW ................... 6 AIR SUPPLY REQUIREMENTS............7 ASSEMBLY ..................8 OPERATION...................9 TROUBLESHOOTING..............10 MAINTENANCE ................11 PARTS LIST & DIAGRAM...............12 SPECIFICATIONS .............. -
Page 4: Safety Precautions
SAFETY PRECAUTIONS CAUTION: FAILURE TO FOLLOW THESE PRESCAUTIONS COULD RESULT IN PERSONNAL INJURY, AND /OR DAMAGE TO PROPERTY WORK ENVIRONMENT 1. Keep the work area clean and tidy. 2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair out of the way. - Page 5 Moving to another work area. 12 Never use the tool if it is defective or operating abnormally. 13. The tool should be serviced as required by your CLARKE dealer. 14. Avoid damaging the tool for example by applying excessive force.
-
Page 6: Overview
AIR INLET LOCKING NUT REGULATOR VALVE The CAT80 Sander is ideal for use in garages and workshops. Random orbit sanders give a virtually scratch - free finish on various surfaces prior to painting or varnishing the finished surface. Unpack your sander should include the following items. Any damage or deficiency should be reported to your CLARKE dealer immediately. -
Page 7: Air Supply Requirements
AIR SUPPLY REQUIREMENTS WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE THOROUGHLY FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND COMPRESSED AIR SUPPLY. • Use only clean, dry, regulated compressed air as a power source. •... -
Page 8: Assembly
1. Remove the plastic blanking plug from the connection port of the tool as shown. 2. Pour 2-3 drops of CLARKE airline oil into the air inlet. This should be done regardless of whether or not a lubricated air supply is to be used. -
Page 9: Operation
2. If the tool is not to be used for longer than 24 hours, run a few drops of CLARKE airline oil into the air inlet and run the tool for a few seconds to ensure that the oil has been well distributed throughout the tool. -
Page 10: Troubleshooting
. y l ACCESSORIES A wide range of accessories are available including filter/regulators, lubricators, high pressure hoses, etc. Contact your CLARKE dealer for further information, or call CLARKE International on 01992 565333. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 11: Maintenance
**Clarke Airline Oil is available from your CLARKE dealer: part no. 3050825. Parts & Service: 020 8988 7400/E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 12: Parts List & Diagram
PARTS LIST AND PARTS DIAGRAM Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 13 PARTS LIST AND PARTS DIAGRAM l f f " " ABRASIVE DISCS Replacement abrasive discs (self adhesive - 6” (150mm) dia) are available from your CLARKE dealer: Fine Part no. 6502097 Medium Part no. 6500809 Coarse Part no. 6502102 Parts & Service: 020 8988 7400/E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 14: Specifications
SPECIFICATIONS l n I " 4 i n i " 6 Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400/E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...