Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Chicago Electric 14 Industrial Cut-off Saw 68104
Summary of Contents for Chicago Electric 14 Industrial Cut-off Saw 68104
-
Page 2: Specifications
WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided, will result in death or serious injury. -
Page 3: Grounding Instructions
12. SECURE WORK. Use clamps or a vise to hold 18. NEVER STAND ON TOOL. Serious injury work when practical. It’s safer than using your could occur if the tool is tipped or if the hand and it frees both hands to operate tool. cutting tool is unintentionally contacted. -
Page 4: Vibration Safety
Grinder Safety Warnings For Your Own Safety Read Instruction • Crystalline silica from bricks and cement or other Manual Before Operating Grinder masonry products • Arsenic and chromium from 1. Wear eye protection. chemically treated lumber 2. Use grinding wheel suitable for speed of grinder. Your risk from these exposures varies, depending 3. -
Page 5: Instructions For Putting Into Use
Instructions for Putting into Use Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. -
Page 6: Tool Set Up
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Release the Trigger and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. -
Page 7: Work Piece And Work Area Set Up
Work Piece and Work Area Set Up 1. Designate a work area that is clean and well-lit. b. To cut at various angles (up to 45°), The work area must not allow access by children adjust the Angle Scale by loosening the two or pets to prevent distraction and injury. -
Page 8: Cleaning, Maintenance, And Lubrication
Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Release the Trigger and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. -
Page 9: Troubleshooting
Troubleshooting Problem Possible Causes Likely Solutions Tool will not start. 1. Cord not connected. 1. Check that cord is plugged in. 2. No power at outlet. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads. -
Page 10: Please Read The Following Carefully
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. -
Page 11: Assembly Diagram
Assembly Diagram Item 68104 For technical questions, please call 1-800-444-3353. Page 11... -
Page 12: Limited 90-Day Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.