Chicago Electric 1624 Set Up And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Chicago Electric Manuals
  4. Saw
  5. 1624
  6. Set up and operating instructions manual
Chicago Electric 1624 Set Up And Operating Instructions Manual

Chicago Electric 1624 Set Up And Operating Instructions Manual

Industrial 14” cut-off saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

set up and operatIng InstruCtIons
distributed exclusively by Harbor freight tools
Visit our website at: http://www.harborfreight.com
read this material before using this product.
failure to do so can result in serious injury.
saVe tHIs manual.
©
Copyright
1997 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
for technical questions or replacement parts, please call 1-800-444-3353.
IndustrIal
14" Cut-off saw
3491 Mission Oaks Blvd., Camarillo, CA 93011
®
. All rights reserved. No portion of this manual or any artwork
1624
®
.
manual revised 09c

Advertisement

Table of Contents
loading

Related Manuals for Chicago Electric 1624

Summary of Contents for Chicago Electric 1624

  • Page 1 Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

  • Page 2: Important Safety Information

    saVe tHIs manual Keep this manual for the safety warn- ings and precautions, assembly, operat- ing, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number).
  • Page 3 DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed. reCommended mInImum wIre gauge for eXtensIon Cords (120 Volt) eXtensIon Cord...

  • Page 4: Grounding Instructions

    or other part that is damaged should be properly repaired or replaced. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

  • Page 5: Cutoff Saw Safety Warnings

    Industrial applications must follow OSHA guidelines. Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or miss- ing, contact Harbor Freight Tools for a replacement. Avoid unintentional starting. Prepare to begin work before turning on the tool.
  • Page 6 those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.) WARNING: Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm.

  • Page 7: Specifications

    speCIfICatIons Electrical Input 120 V~ / 60 Hz / 3.5 HP Motor No Load Speed 3800 RPM Wheel: 14”, 1” arbor Capacities: 3” x 8-1/2” (flat); 4” (pipe) unpaCkIng When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at 1-800-444-3353 as soon as possible.

  • Page 8: Depth Of Cut Adjustment

    VISE STOP (#69) to the desired posi- tion. Tighten the BOLTS. Raise the VISE LEAD SCREW RE- LEASE HANDLE (#89) and slide the VISE FACE (#67) forward until it contacts the stock. Lower the RELEASE HANDLE so that it rests against the LEAD SCREW (#81).

  • Page 9: Maintenance

    maIntenanCe wheel alignment If the Wheel gets out of alignment and begins to contact the BASE (#74), the following procedures must be observed. Secure the Wheel in the locked down position. Tilt the unit on its side. Slightly loosen the four BOLTS (#38) that hold the two PIVOT BLOCKS (#63) in place.

  • Page 10: Please Read The Following Carefully

    please read tHe followIng CarefullY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.

  • Page 11: Assembly Diagram

    assemBlY dIagram record product’s serial number Here: note: If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 1624 for technical questions, please call 1-800-444-3353.

  • Page 12: Limited 1 Year / 90 Day Warranty

    1 Year / 90 daY warrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship.

Table of Contents