Understanding Auto Eq Error Messages - Pioneer AVH-X1600DVD Owner's Manual

Appendix
Additional information
Pandora is unable to play music. Please see your
Device.
Unable to play music from Pandora.
Please check your iPhone.
Please create station. Application on Device.
No station found.
Create a station in the Pandora application on
your iPhone.
No Active Station
No station selected.
Select a station.
Communication error occured. Please reconnect
your device.
If there is no ACK after 10 attempted retries at
750 ms, the accessory should assume that commu-
nication is interrupted and disconnect from
PandoraLink.
Please reconnect your iPhone and try again.
Device has not been registered. Go to "Bluetooth
Connection Menu" to register.
No Bluetooth device found.
Follow the instructions that appear on the
screen.
Connection failed. Press "Connect" to retry.
Bluetooth connection failed.
Follow the instructions that appear on the
screen.
Disconnected. Press "Connect" to reconnect the
device.
Bluetooth connection lost.
Follow the instructions that appear on the
screen.
60
En
MirrorLink
The application list could not be read out.
Failed to load the application list.
! Disconnect the cable from the smartphone,
and then connect the smartphone again after a
few seconds.
! Turn the ignition switch OFF and then to ACC
or ON.
If the error message is still displayed after
performing the above action, reset the
smartphone.
If the error message is still displayed after
performing the above action, please contact your
dealer or an authorized Pioneer Service Station.
There is no supported application on your Mirror-
Link device.
No supported applications can be found.
! Disconnect the cable from the smartphone,
and then connect the smartphone again after a
few seconds.
! Turn the ignition switch OFF and then to ACC
or ON.
If the error message is still displayed after
performing the above action, reset the
smartphone.
If the error message is still displayed after
performing the above action, please contact your
dealer or an authorized Pioneer Service Station.
Communication error occurred.
There was a communication error.
! Disconnect the cable from the smartphone,
and then connect the smartphone again after a
few seconds.
Additional information
! Turn the ignition switch OFF and then to ACC
or ON.
If the error message is still displayed after
performing the above action, reset the
smartphone.
If the error message is still displayed after
performing the above action, please contact your
dealer or an authorized Pioneer Service Station.
Launching the application failed.
Failed to launch the application.
! Disconnect the cable from the smartphone,
and then connect the smartphone again after a
few seconds.
! Turn the ignition switch OFF and then to ACC
or ON.
If the error message is still displayed after
performing the above action, reset the
smartphone.
If the error message is still displayed after
performing the above action, please contact your
dealer or an authorized Pioneer Service Station.
USB connection was temporarily disabled for de-
vice protection. Do not connect this USB device
to the unit. To restart USB, restart the unit.
There is an over current error. Do not use this USB
storage device.
Turn the ignition switch OFF and then to ACC or
ON.
If the error message is still displayed after
performing the above action, please contact your
dealer or an authorized Pioneer Service Station.
Understanding auto EQ error
messages
When correct measurement of the car's interior
acoustic characteristics is not possible using
auto EQ, an error message may appear on the
display. In such cases, refer to the table below to
see what the problem is and how it may be cor-
rected. After checking, try again.
Error messages are written in bold and causes
in regular, non-indented text. Regular, indented
text is used to indicate actions to be taken.
Please connect the microphone for
measurement. When finished, please push
HOME key.
The microphone is not connected.
Plug the optional microphone securely into the
jack.
Error. Please check xxxx speaker.
The microphone cannot pick up the measuring tone
of a speaker.
! Confirm that the speakers are connected
correctly.
! Correct the input level setting of the power
amp connected to the speakers.
! Plug the microphone securely into the jack.
Error. Please check noise.
The surrounding noise level is too high.
! Stop your car in a place that is quiet, and
switch off the engine, air conditioner and heater.
! Set the microphone correctly.
Error. Please check battery.
Power is not being supplied from the battery to this
unit.
! Connect the battery correctly.
! Check the battery voltage.