Toshiba B-EX Series Operation Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Label Maker
  5. B-EX Series
  6. Operation manual

Toshiba B-EX Series Operation Manual

Hide thumbs Also See for B-EX Series:
Table of Contents

Advertisement

Quick Links

TOSHIBA Label Printer
B-EX Series
B-EX Setting Tool Operation Manual
Second Edition: January 25, 2012

Advertisement

Table of Contents
loading

Related Manuals for Toshiba B-EX Series

Summary of Contents for Toshiba B-EX Series

  • Page 1 TOSHIBA Label Printer B-EX Series B-EX Setting Tool Operation Manual Second Edition: January 25, 2012...

  • Page 2: Table Of Contents

    Table of Contents 1. INTRODUCTION ............................1 UPPORTED RINTERS .......................... 1 OFTWARE ICENSE GREEMENT ................................1 EATURES ..........................2 UTLINE OF THE UNCTIONS ................................2 OTATION ........................3 CREENS SED IN OCUMENT ..........................3 RADEMARK AND OPYRIGHT ............................ 4 PERATIONAL ONDITIONS Software (Operation System) ..........................
  • Page 3 Create External Character Tab........................72 Test Print Tab..............................76 6. APPENDIX ............................79 RROR ESSAGE ............................... 82 ETUP TEMS General Tab ..............................82 General (2) Tab.............................. 85 Device Tab..............................86 LAN Tab ................................. 87 WLAN Tab ..............................88 WLAN (2) Tab ..............................90 RFID Tab ...............................

  • Page 4: Introduction

    CLAIMS BY A THIRD PARTY. 8. TOSHIBA TEC or its licenser will terminate this Agreement if you fail to comply with any of this terms and conditions. Upon the termination of this Agreement, you agree to uninstall the Software and return it to TOSHIBA TEC.

  • Page 5: Outline Of The Functions

    Outline of the Functions The Product provides the following functions. There are some restrictions depending on the communication method. Communication method Function Description One-to-one Collective Displaying the Obtains and displays the current parameter settings. Enabled Disabled parameters Setting the parameters Changes the specified parameter settings.

  • Page 6: Screens Used In This Document

    7 Professional and Microsoft Windows 7 Home Premium: Windows 7 All technologies other than the above are exclusive property of TOSHIBA TEC. Copyright of TOSHIBA TEC in Japan and other countries is expressed as: Copyright© 2011-2012 TOSHIBA TEC CORPORATION. All Rights Reserved.

  • Page 7: Operational Conditions

    The Setting Tool and Downloader must be used by the Administrator or under instructions of the Administrator. TOSHIBA TEC shall not be liable for any outcome resulted from a failure to follow the above instructions (both the Product and the Supported Printers).

  • Page 8: Installation

    2. Installation Installation Procedure Double-click the setup program (BEXToolSetup.exe) of the Product. Note: With Windows Vista/7, the User Account Control dialog box may appear. In that case, click [Allow] to continue. The InstallShield Wizard starts. Click [Next]. The [License Agreement] screen appears. When you agree, click [I accept the terms of the license agreement] and click [Next].
  • Page 9 The [Selection of Initial Setting] screen appears. Select a language used for the Product, a printer model to be connected and its destination from the pull down menus. These are changeable after installation. The [Start Copying Files] screen appears. Check the descriptions under [Current Settings] and click [Next] when the descriptions are correct.

  • Page 10: Uninstallation

    Uninstallation Select [Start] - [Control Panel] - [Programs and Features]. Note: With Windows Vista/7, the User Account Control dialog box may appear. In that case, click [Allow] to continue. Choose the Product on [Uninstall or change a program] screen, then click [Uninstall]. The dialog box appears to confirm the removal of the Product.

  • Page 11: Start-Up

    When the USB serial number is changed, the setting on the printer will be automatically changed properly. When the command control code is changed, the environment setting will be automatically changed accordingly. Select [Start] - [All Programs] - [TOSHIBA TEC] - [B-EX Setting Tool] - [B-EX Setting Tool] and click [B-EX Setting Tool].

  • Page 12: Preparation

    4. Preparation Main Screen When the Product is started, the [Printer Setting] screen is displayed. Menu bar Menus to support each function are provided. Menu icon Menu icons are placed in this area. When an icon is clicked, the corresponding menu screen appears on the main view area. The icon being selected is highlighted.
  • Page 13 ▪ Memory Management Tab: Processing related to the memory Download: Downloads the printer firmware or BASIC program. ▪ Firmware Download Tab: Downloads printer firmware ▪ BASIC Download Tab: Downloads the BASIC program ▪ Create HTML/XML ROM Tab: Creates HTML/XML ROM file Tool: Other functions ▪...

  • Page 14: Menus

    Menus File [Import...] This menu is used to retrieve setup information from a specified file. This menu is selectable only when the [Parameter Setting] screen is activated. When this menu is clicked, the [Import] screen is displayed. Specify a setup information file, click [Open], and the file import is started.
  • Page 15 [Export...] This menu is used to store setup information in a specified file. This menu is selectable only when the [Parameter Setting] screen is activated. When this menu is clicked, the [Export] screen is displayed. Specify a file where the setup information is saved, click [Save], then the file export is started.

  • Page 16: Edit

    Edit [Enable All] This menu is used to check all checkboxes on all tabs. This menu is selectable only when the [Parameter Setting] screen is activated. [Disable All] This menu is used to uncheck all checkboxes on all tabs. This menu is selectable only when the [Parameter Setting] screen is activated. [Enable All in Tab] This menu is used to check all checkboxes on the tab.

  • Page 17: View

    View [Restore to Default] This menu is used to restore the all setting values on the all tab pages to the default. This menu is selectable only when the [Parameter Setting] screen is activated. [Restore Display to Default] This menu is used to restore all setting values on the selected tab page to the default. While the [Parameter setting] screen is activated, the setting values only on the displayed tab page are restored to the default.

  • Page 18: Help

    Help [Contents...] This menu is used to display the main screen for Help. [About...] This menu is used to display version information.

  • Page 19: Printer Setting

    Printer Setting The printer setting menu enables selecting a printer model to be connected and configuring the interface used. When the [Printer Setting] icon on the menu icon area is clicked, and the following screen is displayed. The setting is not saved by a member of the Users. [Printer] Select a printer model to be connected.
  • Page 20 When [Yes] is clicked, the printer model is changed. When [No] is clicked, the printer model remains unchanged. B-EX4T1-G, B-EX4T1-T, B-EX4T2-G, B-EX4T2-T, B-EX4T2-H, B-EX6T2-G, Options B-EX6T2-T * B-EX6T2-G and B-EX6T2-T are not approved at present. [Destination] Select the destination of the printer to be connected. The default is the destination selected during the installation.

  • Page 21: Usb

    [Serial Number] Enter the USB serial number assigned to the connected printer. If this is not entered, the printer to be connected is automatically selected. The Serial number checkbox is unchecked as default. When checked, an entry of the serial number is enabled. Enter 12 one-byte characters using "0"...

  • Page 22: Lan

    [Host Name or IP Address] Enter the host name or IP address set for the connected printer. The default right after the installation is "192.168.10.20". When specifying the printer with the IP address, use "X.X.X.X" format. When specifying the printer with the host name, enter up to 32 alphanumeric characters. The setting is saved upon changed, and reflected in the header view.

  • Page 23: Multi Lan

    Multi LAN [Printer List] Multiple printers on the network to access at one time are displayed. No printer is specified as default right after the installation. Changes are saved upon changed. Collective processing is executed in ascending order of the number. When no printer is registered in the list, an error occurs at the start of communication with the printer.
  • Page 24 However, when 50 printers have been registered in the list, the [Add] button becomes disabled. The maximum number of registrable printers in the list is 50. If a printer having the same [Host Name or IP Address] already exists, the addition of a new printer is not allowed.

  • Page 25: Com

    [Port Number] Select the COM port number used for communication. The default right after the installation is "1". The setting is saved upon changed, and reflected in the header view. Range 1 to 99 [Baud Rate] Select the baud rate for the RS-232C port that has been set for the connected printer. The default right after the installation is "9600 bps".
  • Page 26 [Stop Bit] Select the stop bit for the RS-232C port that has been set for the connected printer. The default right after the installation is "1 bit". The setting is saved upon changed, and reflected in the header view. Options 1 bit, 2 bits...

  • Page 27: Environment

    Environment Set the operating environment for the Product. When [Options] at the right end on the header view is clicked, the [Environment] screen appears. The setting is not saved by a member of the Users. [Language] Select a language used to display the Product. The language selected during the installation has been set as default.
  • Page 28 Change the value when the control code is set to "Manual" for the printer. Range 00 to FF [Code 2] Enter the same value in hex. format that is set for the connected printer. The default right after the installation is "0A". [Code 2] is editable only when "Manual"...

  • Page 29: Password Change

    Password Change [Old Password] When the password has been set, enter the current password. It is not necessary to enter a password when this is the first time to set the password. The entered password is displayed with hidden characters. [New Password] Enter a new password.

  • Page 30: Processing Screen

    Processing Screen When processing involving communication between the printer and the Product is executed, the processing screen is displayed. The progress bar screen is displayed during the processing, and the completion screen appears when the processing is completed. Progress Bar Screen Title Processing being executed is displayed.

  • Page 31: Completion Screen

    Completion Screen Title Processing executed is displayed. The same title shown on the progress bar screen is taken over. Progress status When the progress bar reaches 100% and the final result is indicated by text. In the case of normal end, the normal end icon is displayed. If the processing does not end normally due to an error, the abnormal end icon is displayed.

  • Page 32: Progress Status

    Progress Status Textual information about the processing in progress is added to the progress status as needed. Progress status format: ["Host Name or IP Address"], "Processing", "Process", " Detailed status" ("Error code") Host Name or IP Address When the Multi LAN is selected for the interface, the host name or IP address of the connected printers is displayed.
  • Page 33 BASIC main program is being sent to the printer in the BASIC Download Updating the main program... processing. Transmission and update of the main program are in progress. BASIC system mode program is being sent to the printer in the BASIC Updating the system mode Download processing.

  • Page 34: Printer List Screen

    Printer List Screen The following screen appears when collective processing is executed for multiple printers connected to the network. You can check the applicable printers and exclude unnecessary printers on this screen. This screen is displayed only when Multi LAN is used. List The printers registered to the [Printer List] for the Multi LAN are displayed.

  • Page 35: Functions

    5. Functions Parameter Setting The parameter setting menu enables configuring or obtaining the printer parameter settings. When the [Parameter Setting] icon on the menu icon area is clicked, the [Parameter Setting] screen is displayed. Once the processing is executed, the printer enters the parameter setting mode. Restore the printer to the online mode after the all processing is completed.
  • Page 36 The [Parameter Setting] screen has [General], [General (2)], [Device], [LAN], [WLAN], [WLAN (2)] and [RFID] tabs. When any of these tabs is clicked, the selected tab page is displayed to allow setting the related parameters. The parameter setting values are obtained from the printer at one time for the all controls in the all tab pages.
  • Page 37 When this button is clicked after getting the printer settings, the progress status screen is displayed. When the printer returns to online mode, the screen is closed. The completion screen appears in the case of an abnormal end. Mode shift is automatically executed when another menu screen is opened or the Product is terminated with this button displayed.

  • Page 38: General Tab

    General Tab [Image] Group [Character Code]: Select a character code table to be applied to the printer font. Default PC-850 PC-850, PC-8, PC-852, PC-857, PC-851, PC-855, PC-1250, PC-1251, PC-1252, Options PC-1253, PC-1254, PC-1257, LATIN9, Arabic, PC-866, UTF-8 [Zero Font]: Select whether or not a slash is attached to the printer font character "0". Note that the no slash is attached for the following fonts, regardless of settings.
  • Page 39 [MaxiCode Spec]: Select a type of barcode font to create a MaxiCode. Default TYPE 1 Options TYPE 1 (Compatible with current version), TYPE 2 (Special specification) [Kanji Code]: Select a type of Kanji font code. Default TYPE 1 Options TYPE 1 (Windows code), TYPE 2 (Original code) [Supply] Group [Energy Type (Transfer)]: Select a print head energy control type for thermal transfer printing.
  • Page 40 [Display] Group [LCD Language]: Select a language of messages to be displayed on the LCD. JA: Japanese Default Other than JA: English English, German, French, Dutch, Spanish, Japanese, Italian, Portuguese, Options Simplified Chinese [Contrast]: Set an even number for the LCD contrast fine adjustment. When an odd number is set, it will be automatically corrected to an even number.
  • Page 41 Default 15 min Range 1 to 240 min [Action] Group [Media Load]: Select whether or not to feed media to the home position. Default Disable B-EX4T1-G / B-EX4T1-T: Disable, Standard, ECO, ECO (with Back Feed) Options Other than B-EX4T1-G / B-EX4T1-T: Disable, Standard, ECO [Forward Wait]: Select whether an automatic forward feed is performed after an issue is enabled or disabled.

  • Page 42: General (2) Tab

    General (2) Tab [Position Adjustment] Group [Feed]: Set a fine adjustment value for the stop position in units of 0.1 mm. When the value is negative (-), the feed length becomes longer. The fine adjustment value set by the Position Fine Adjust command [AX] is displayed in the left box. When the parameter is not retrieved, the value in the left box becomes zero (0).
  • Page 43 [X-coordinate]: Set a fine adjustment value to offset the print position perpendicular to the paper feed direction in units of 0.1 mm. When the value is negative (-), the upper right reference coordinate shifts to the left from the zero point. Default 0.0 mm Range...
  • Page 44 [Product] Group [Printer Serial No.]: The serial number specific to the printer is displayed. This setting cannot be changed. [SHELL]: The status of the SHELL function is displayed. This setting cannot be changed. [Sensor] Group [Reflective Sensor Threshold Select]: Select how to set the threshold for the reflective sensor. Default Command Set Options...
  • Page 45 [Password] Group [System Mode Password]: Select whether or not the password used for entering SYSTEM mode is enabled. To set this field, the old password is required. When you enter an incorrect old password, you cannot change the password. [New Password]: Set a password to be used for entering SYSTEM mode.

  • Page 46: Device Tab

    Device Tab [RS-232C] Group [Baud Rate]: Set a communication baud rate for the RS-232C port. Default 9600 bps Options 2400 bps, 4800bps, 9600 bps, 19200 bps, 38400 bps, 115200 bps [Data Length]: Select the data length for the RS-232C port. Default 8 bits Options...
  • Page 47 [Control]: Select the method of flow control to be used by the RS-232C port. QQ: READY/BUSY Default Other than QQ: XON+READY AUTO XON+READY AUTO, XON/XOFF AUTO, READY/BUSY RTS, XON+XOFF, Options READY/BUSY [Centro.] Group [ACK/BUSY]: Select Centronics ACK /BUSY signal timing. Default TYPE 1 TYPE 1 (BUSY goes LOW at the same time as ACK goes HIGH.),...

  • Page 48: Lan Tab

    LAN Tab [TCP/IP] Group [LAN I/F]: Select whether to enable or disable the communication via wired LAN or wireless LAN. Default Enable (AUTO) Options Disable, Enable (AUTO), Enable (Wired LAN), Enable (Wireless LAN) [IP Address]: Set an IP address. Default 192.168.10.20 Range 0.0.0.0 to 255.255.255.255...
  • Page 49 [Socket]: Select whether or not socket communication is enabled. Default Enable Options Disable, Enable [Port Number]: Set a port number used for socket communication. Default 8000 Range 0 to 65535 [WEB Printer]: Select whether or not the Web server function is enabled. Default Disable Options...
  • Page 50 [WINS]: Select whether or not the WINS protocol is enabled. When "Enable (STATIC)" is selected, [WINS Server Address] is used. When "Enable (DHCP)" is selected, [DHCP] is used. Default Disable Options Disable, Enable (STATIC), Enable (DHCP) [WINS Server Address]: Set the IP address of the WINS server. Default 0.0.0.0 Range...

  • Page 51: Wlan Tab

    WLAN Tab [WLAN Basic] Group [Communication Standard]: Select the wireless LAN standard. Default 802.11b/g Options 802.11b, 802.11g, 802.11b/g [WLAN Detail] Group [ESS ID]: Set an ESS ID, using up to 32 alphanumeric characters. Default TOSHIBATEC [Beacon Transmitting Interval]: Select an interval between transmissions to the beacon. Default 1000 msec Range...
  • Page 52 [802.11b] Group [Channel]: Set a channel for IEEE 802.11b. The printer corrects channels that cannot be used due to country code settings. Default Range 1 to 14 [Baud Rate]: Select the maximum transmission rate for IEEE 802.11b. The transmission rate is adjusted to a value enabling communication by the communicating device. Default 11 Mbps Options...
  • Page 53 [(4) EAP Method]: Select the EAP method. Displayed options depend on the [(1) Connection Mode], [(2) Encryption] and [(3) Network Authentication] settings. Default Disable Disable, EAP-MD5, EAP-TLS, EAP-TTLS, LEAP, LEAP (NetworkEAP), PEAP, Options PEAP (w/o Cert.), EAP-FAST < Authentication System Settings > (1) Connection Mode (2) Encryption (3) Network Authentication...
  • Page 54 [Input Type]: Select the code for entering a WEP key. When the code is changed, the WEP key is cleared. Default Options HEX, ASCII [WEP Key #1] [WEP Key #2] [WEP Key #3] [WEP Key #4]: Select the WEP key used for encrypting the authentication system. Select the WEP key size and enter the WEP key.

  • Page 55: Wlan (2) Tab

    WLAN (2) Tab [WPA-PSK] Group [Pre Shared Key]: Set a key to be used for WPA encryption in network authentication, using 8 to 64 alphanumeric characters. Since the key is security information, it is displayed with hidden characters except when it is being entered.
  • Page 56 [Supplicant] Group [Server Certificate]: Set an absolute path to the server certificate file to be transmitted. button is used to select the path on the file selection screen. When no path is entered, data transmission is not performed. When entering a path to a blank file without data, you can disable the current settings. Setting a non-existent file results in an error.
  • Page 57 [PAC File Password]: Set the password for the PAC file used for the Manual Provisioning. Up to 32 digits of 1-byte alphanumeric characters can be set. [CCX] Group [CCX Options]: Select whether to enable or disable the CCX options. Default Disable Options Disable, Enable...

  • Page 58: Rfid Tab

    RFID Tab [Module] Group [Module Type]: RFID module type installed in the printer is displayed. Default None Options None, H1 (HF Band), H2 (HF Band), U2 (UHF Band) [Tag Type]: Select the RFID tag type. The displayed options differ depending on the RFID module type. Default NONE None: NONE, I-Code, Tag-It, C220, IOS15693, C210, C240, C320, EPC C1 Gen2...
  • Page 59 [Q Value]: Set the sensitivity for detecting RFID tags. Default Range 0 to 15 [AGC Threshold]: Set the threshold value used to determine an RFID tag is defective or not. Default Range 0 to 15 [Write AGC Threshold]: Set the threshold value used to determine whether or not to write data to RFID tags. Default Range 0 to 15...

  • Page 60: Maintenance

    Maintenance The Maintenance menu enables the self diagnosis and memory management. When the [Maintenance] icon on the menu icon area is clicked, the [Maintenance] screen is displayed. When the interface type is LPT1, LPT2 or LPT3, this menu cannot be used. Self Diagnosis Tab [Maintenance Counter Info] The maintenance counter values are displayed.
  • Page 61 After refreshing the display, "ALL" is selected. ALL, ADJUST, PARAMETER SETTING, PANEL, STRAGE AREA, USB, RS-232C, Options CENTRO, LAN/WLAN, RFID, RTC [Refresh] Current printer information is obtained, and the displayed maintenance counter, firmware information and parameter setting values are updated. When this button is clicked, the processing starts.
  • Page 62 [Save Printer Info...] Current printer information is obtained, and saved in a file. When this button is clicked, the file selection screen is displayed. Select a file where the printer information is stored, click [Save], then the processing is started. When Multi LAN is selected for the interface, a file is created for each of the connected printers.
  • Page 63 [Initialize...] A RAM clear is performed to initialize to the parameter setting values for the selected destination. When this button is clicked, the following confirmation message is displayed. When [Yes] is clicked, the processing starts. When [No] is clicked, the processing is canceled. When Multi LAN is selected for the interface, the [Printer List] screen is displayed to allow choosing the printers on which the parameter clear is performed.

  • Page 64: Memory Management Tab

    Memory Management Tab [Memory Info] The printer memory information is displayed. Refreshing the display causes the latest data to be shown. When Multi LAN is selected for the interface, this function is disabled. [Refresh] The current information of the printer memory is obtained and the display is updated. When this button is clicked, the processing starts.
  • Page 65 [Bitmap External Character Storage Area] Set the area size for storing bitmap external characters. Default 1792 KB Options 0 to 3072 KB (in units of 128KB) [BASIC File Storage Area] Set the area size for storing the BASIC program. When "No Change" is selected, existing data is retained without allocating the BASIC file storage area. Default 0 KB Options...
  • Page 66 When [Yes] is clicked, the processing starts. When [No] is clicked, the processing is canceled. When Multi LAN is selected for the interface, the [Printer List] screen is displayed to allow choosing the printers of which memory is formatted. When the processing starts, the progress status screen is displayed. When the processing is completed, the completion screen is displayed.

  • Page 67: Download

    If a power failure occurs during a firmware updating, the printer may not start up. Even when the printer can normally start up, download the firmware again. If cannot, please contact TOSHIBA TEC sales representative. [ROM List] ROM files of the firmware to be downloaded to the printer are displayed.
  • Page 68 If the specified file is not a ROM file, or if the specified ROM file is not for the printer model selected for the Product, the error message is displayed. Up to eight ROM files can be added. One file per program section is accepted. In the case second file is chosen for a program section, the following confirmation message is displayed.

  • Page 69: Basic Download

    BASIC Download Be sure to avoid the environment where a power failure may occur in the middle of the downloading. If a power failure occurs during a downloading, retry the operation. [Memory Allocate] Select whether or not the on-board flash memory is divided and allocated to different types of data. The checkbox has not been checked as default.
  • Page 70 [BASIC File Storage Area] Set the area size for storing the BASIC program. When "No Change" is selected, existing data is retained without allocating the BASIC file storage area. Set 512KB (4 blocks) or more. Default 512 KB Options No Change, 0 to 3072 KB (in units of 128KB) [PC Save Storage Area] The storage area size for printer commands is displayed.
  • Page 71 Data file Click the button to open the file selection screen. Select a BASIC data file, click [Open], then the full path of the file is displayed. The [BASIC Data File] does not become effective unless a file is selected. When reading a file or creating download data failed, the error message is displayed.

  • Page 72: Create Html/Xml Rom

    Create HTML/XML ROM [ROM Type] Select a ROM file type to be created. The "Load Address" and "Size" differ depending on the ROM file type. Default HTML/XML Options HTML/XML [Source Path] Specify the location where the HTML/XML files are stored. Click the button, and the folder selection screen is displayed.
  • Page 73 \JPN\HTML folder: File for Japanese language \JPN\PASS folder: File for Japanese language \MAIL folder: File for emails \MAIL\TEXT folder: File for emails The file size and the ratio to the maximum size in percentage are displayed under the [Source List]. [ROM List] Data configuration of the created ROM file is displayed.

  • Page 74: Tool

    Tool The functions useful for operating the printer are provided. When the [Tool] icon on the menu icon area is clicked, the [Tool] screen is displayed. Tool Tab [Send File...] A specified file is sent to the printer in binary format. When this button is clicked, the file selection screen is displayed.

  • Page 75: Create External Character Tab

    Create External Character Tab [Specification Method] How to specify the bitmap file path is selectable. Select the "File" when an external character is created from one bitmap file. Select the "Folder" when an external character is created from more than one bitmap file. Default File Options...
  • Page 76 When no monochrome bitmap file with proper name is found in the specified folder, the error message is displayed. Bitmap file name format G_"Type""Code" (_"Left Offset"_"Top Offset"_"Character Spacing").bmp <Example> When Type = 01, Code = 20: G_0120.bmp or G_0120_0_0_0.bmp When Type = 51, Code = FFFF: G_51FFFF.bmp or G_51FFF_0_0_0.bmp Restriction on the bitmap file When [Type] = "41", the size shall be 16 x 16 dots.
  • Page 77 [Top Offset] Set a value for the top offset from the reference coordinate. When any of "41" to "44" is set for the [Type], this becomes invalid. When the "Folder" is selected for the [Specification Method], this becomes invalid. Default 0 dot When [Location] = "Onboard Flash Memory": 0 to 719 dots Range...
  • Page 78 [Output File] Specify the file where the external character is stored. Click the button, and the file selection screen is displayed. Specify a file, click [Save], and the full path is displayed in the file name. The file extension is "gai". After the specified file is initialized, the external character is stored in it.

  • Page 79: Test Print Tab

    Test Print Tab [Print Pattern] Select a print pattern for the test print. Default Slant Lines (1 dot) Options Slant Lines (1 dot), Slant Lines (3 dots), Characters, Barcodes [Print Condition] [Issue Count] Set the print count. Default Range 1 to 9999 [Print Speed] Select a print speed.
  • Page 80 [Sensor] Select a sensor to be used. Default None None, Reflective, Transmissive, Transmissive (Preprinted Labels), Options Reflective (Manual) [Issue Mode] Select an issue mode. Default Batch Options Batch, Cut After Every Page, Peel-off [Print Method] Select a print method. Default Thermal Transfer B-EX4T1-G / B-EX4T1-T: Thermal Transfer, Thermal Transfer (Ribbon Saving), Direct Thermal,...
  • Page 81 Slant Lines (1 dot) Slant Lines (3 dot) Characters Barcodes...

  • Page 82: Appendix

    6. Appendix Error Message List Message Explanation Login Dialog The password is not correct. The entered password is incorrect. Enter a correct password. The password is case-sensitive. Environment Dialog The same value is set for all of "Code 1", "Code 2" The same value is set for all of "Code 1", "Code 2"...
  • Page 83 The entered value for "WEP Key #'number'" on the The number of characters entered for "WEP Key WLAN tab page is incorrect. #'number'" is insufficient. ('number': 1 to 4) When using hex. format, enter a 10-digit or 26-digit hex. code. When using ASCII, enter a 5-digit or 13-digit character string.
  • Page 84 Selected file is not a monochrome bitmap file. The specified file is not a monochrome bitmap file. Select a file in the correct format. The specified file exceeds the maximum width or The width or height of the bitmap exceeds the maximum height of the external character.

  • Page 85: Setup Items List

    Setup Items List General Tab Setup group Setup item Options or range Default Image Character Code PC-850 PC-850 PC-8 PC-852 PC-857 PC-851 PC-855 PC-1250 PC-1251 PC-1252 PC-1253 PC-1254 PC-1257 LATIN9 Arabic PC-866 UTF-8 Zero Font without Slash without Slash with Slash EURO Font Code 20 to FF MaxiCode Spec...
  • Page 86 Energy Type (Direct) Standard Standard Reserve 1 Reserve 2 Reserve 3 Reserve 4 Reserve 5 Reserve 6 Reserve 7 Reserve 8 Reserve 9 Ribbon Near End Disable Disable 30 m 70 m Label/Ribbon End TYPE 1 TYPE 1 TYPE 2 B-EX4T1-G / B-EX4T1-T: Disable JA: Tag...
  • Page 87 Head Up Cut/Rewinder Disable Disable Enable Back Feed Speed Standard Standard Peel Off Peel Off Status Disable Disable Enable Pre Peel Off Disable Disable Enable Disable Standard Standard Oracle Standard (External Memory) Oracle (External Memory) SAP (External Memory)

  • Page 88: General (2) Tab

    General (2) Tab Setup group Setup item Options or range Default Position Feed -50.0 to +50.0 (mm) Adjustment Cut/Peef Off -50.0 to +50.0 (mm) Back Feed -9.9 to +9.9 (mm) X-coordinate -99.5 to +99.5 (mm) Tone Adjustment Thermal Transfer -20 to +10 Direct Thermal -20 to +10 Command...

  • Page 89: Device Tab

    Device Tab Setup group Setup item Options or range Default RS-232C Baud Rate 2400 bps 9600 bps 4800 bps 9600 bps 19200 bps 38400 bps 115200 bps Data Length 7 bits 8 bits 8 bits Parity None JA: Even Even Other than JA: None Stop Bit...

  • Page 90: Lan Tab

    LAN Tab Setup group Setup item Options or range Default TCP/IP LAN I/F Disable Enable (AUTO) Enable (AUTO) Enable (Wired LAN) Enable (Wireless LAN) IP Address 0.0.0.0 to255.255.255.255 192.168.10.20 Subnet Mask 0.0.0.0 to 255.255.255.255 255.255.255.0 Default Gateway 0.0.0.0 to255.255.255.255 0.0.0.0 Protocol Disable Enable...

  • Page 91: Wlan Tab

    WLAN Tab Setup group Setup item Options or range Default WLAN Basic Communication Standard 802.11b 802.11b/g 802.11g 802.11b/g WLAN Detail ESS ID 0 to 32 characters TOSHIBATEC Beacon Transmitting Interval 1 to 65535 (msec) 1000 Roaming Threshold 0 to 99 Country Code Displayed only when obtained.
  • Page 92 Default Key Input Type ASCII WEP Key #1 Disable Disable 40 bits ASCII: Fixed at 5 chars. HEX: Fixed at 10 chars. 104 bits ASCII: Fixed at 5 chars. HEX: Fixed at 10 chars. WEP Key #2 Disable Disable 40 bits ASCII: Fixed at 5 chars.

  • Page 93: Wlan (2) Tab

    WLAN (2) Tab Setup group Setup item Options or range Default WPA-PSK Pre Shared Key 8 to 64 characters 00000000 Account User Name 0 to 32 characters Blank Password 0 to 32 characters Blank 802.1X Reauthentication Interval 2 to 4320 (min) Supplicant Server Certificate Filename: MAX_PATH character...

  • Page 94: Rfid Tab

    RFID Tab Setup group Setup item Options or range Default Module Module Type None None H1 (HF Band) H2 (HF Band) U2 (UHF Band) Tag Type NONE NONE I-Code Tag-It C220 ISO15693 C210 C240 C320 EPC C1 Gen2 Country Displayed only when obtained. Blank UHF Setting Power Level...

Table of Contents