Philips CMP200 User Manual
Hide thumbs
Also See for CMP200:
- User manual (15 pages) ,
- User manual (2 pages) ,
- Service manual (16 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Philips CMP200
Summary of Contents for Philips CMP200
- Page 1 Register your product and get support at www.philips.com/welcome User manual...
-
Page 3: Table Of Contents
Contents 1 Important Safety Notice 2 Your car power amplifier Introduction What’s in the box Overview of the main unit 3 Installation Installation Connect speakers Connect car audio Connect power 4 Use your power amplifier Select crossover frequency mode Adjust frequency Adjust input level Adjust bass boost About the protector indicator Replace fuse 5 Product information... -
Page 4: Important
1 Important Any changes or modifications made to this device that are not expressly approved by Philips Consumer Lifestyle may void the user’s authority to operate the equipment. Safety 2009 © Koninklijke Philips Electronics N.V. All rights reserved. • Read and understand all instructions Specifications are subject to change without before you use the apparatus. -
Page 5: Your Car Power Amplifier
2 Your car power Overview of the main unit amplifier Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Introduction With the amplifier, you can enjoy high quality sound performance with powerful bass and beats. - Page 6 j POWER (GND/REM/+12V) • Connect +12V DC power cable, ground wire and remote wire.. k Fuse: 30A x 2 l SPEAKER OUTPUT • Connect to speakers or subwoofers.
-
Page 7: Installation
3 Installation Connect speakers Installation Note • Use speakers with an impedance of 2 to 8 ohm (4 to 8 ohm when used as a bridged amplifier). You can mount the amplifier either under a seat • Match the “left”, “right”, “+” and “-” terminals or on the rear tray. -
Page 8: Connect Car Audio
Connect car audio Option 1: High level input connection Connect the amplifier to your car audio with the supplied High level input connector. Left speaker Car audio unit Right speaker White Grey White / Black Grey / Black Option 2: Line input connection Connect the amplifier to the car audio with an RCA cable (not supplied) Car audio unit LINE OUT... -
Page 9: Connect Power
Connect power Make the power connection as illustrated below: GND socket. • Connect the ground wire from the car to the • Connect the remote wire from the car audio to the REM socket. √ With this connection, you can turn on/off the amplifier with the car audio. +12V socket. -
Page 10: Use Your Power Amplifier
4 Use your power Rotate FREQ to select frequency. amplifier Select crossover frequency mode Adjust input level You can select crossover frequency mode as below: You can adjust the input voltage from 0.3V to HPF (high-pass- Select this mode when filter) mode mid-range speakers and Rotate INPUT LEVEL to adjust input... -
Page 11: About The Protector Indicator
If this happens, please: If the fuse gets damaged immediately after it has been replaced, there may be an internal malfunction. In such case, consult your Philips Take out the disc or tape and turn off the dealer. car audio. -
Page 12: Product Information
5 Product information Note • Product information is subject to change without prior notice. Power output (RMS) - 4 ohm 125W x 2 - 4 ohm (bridged) 380W x 1 - 2 ohm 190W x 2 Total harmonic distortion 0.01% Signal to noise ratio 106dB Channel separation... -
Page 13: Troubleshooting
If you encounter problems when using this apparatus, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site (www.philips.com/welcome). When you contact Philips, ensure that the apparatus is nearby and the model number and serial number are available. - Page 14 © 2009 Koninklijke Philips Electronics N.V. All rights reserved. Document order number: CMP200_55_UM_V3.1...