Download  Print this page
   

Advertisement

Register your product and get support at
www.philips.com/welcome
A
CMP100
B
EN
User manual
RU
Руководство пользователя
2. Your car power amplifier
English
Congratulations on your purchase, and welcome to Philips! To fully
1. Important
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
Safety
Introduction
Read and understand all instructions before you use the apparatus.
With the amplifier, you can enjoy high quality sound performance with
If damage is caused by failure to follow instructions, the warranty does
powerful bass and beats.
not apply.
This unit is designed for negative ground (earth) 12 V DC operation only.
What's in the box
Use only the supplied mounting hardware for a safe and secure installation.
Check and identify the contents of your package:
Do not connect any active speakers (with built-in amplifier) to the speaker
Amplifier
a
terminals of the unit. Doing so may damage the active speakers.
To ensure safe driving, adjust the volume to a safe and comfortable level.
b
Screw_4x25mm (x4)
To avoid short circuit, do not expose the apparatus to rain or water.
c
Fuse (x2)
Never expose the apparatus to direct sunlight, naked flames or heat.
Hi input connector (x1)
Clean the apparatus with soft, damp cloth. Never use substances such as
d
alcohol, chemicals or household cleaners on the apparatus.
e
Volume controller
Notice
Overview of the main unit
INPUT L/R
Environmental information
a
Connect car audio with RCA cable.
All unnecessary packaging has been omitted. We have tried to make the
packaging easy to separate into three materials: cardboard (box), polystyrene
HI INPUT
b
foam (buffer) and polyethylene (bags, protective foam sheet.)
Connect car audio with the supplied high input connector.
Your system consists of materials which can be recycled and reused if disassembled
c
INPUT LEVEL
by a specialized company. Please observe the local regulations regarding the
Adjust input level (0.3V to 6V).
disposal of packaging materials, exhausted batteries and old equipment.
BASS BOOST
d
Any changes or modifications made to this device that are not expressly
Boost the frequencies at around 45Hz to a maximum of 12dB.
approved by Philips Consumer Lifestyle may void the user's authority to
e
SUBWOOFER
operate the equipment.
Adjust low-pass-f
2009 © Koninklijke Philips Electronics N.V. All rights reserved.
f
PROTECT
Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips
Light in red when the PROTECTOR is activated.
Electronics N.V. or their respective owners. Philips reserves the right to change products at any time
without being obliged to adjust earlier supplies accordingly.
POWER
g
Light in blue when power is turned on.
C
a
b
c
d
e
D
a
REMOTE
LEVEL CONTROL
SUB
SUBSONIC
WOOFER
ON OFF
30Hz
320Hz
i
h
g
f e
d
c
b
a
b
j
k
l
SUBSONIC ON/OFF
h
Switch on or off the subsonic filter.
REMOTE LEVEL CONTROL
i
External remote
controller for volume level control.
POWER (GND/REM/+12V)
j
Connect +12V DC power cable, ground wire and remote wire.
k
Fuse: 30Ax2
l
SPEAKER OUTPUT
Connect to subwoofers.
A
3. Installation
Installation
C
You can mount the amplifier either under a seat or on the rear tray.
Note
To avoid interference, do not place the amplifier too close to the car audio or antenna.
B
The supplied mounting screws are 25mm long. Make sure that the mounting
board is thicker than 25mm.
1
Place the unit on the location for installation.
2
Mark the positions of the four screw holes.
3
Drill the holes with driller of approximately 4mm in diameter.
4
Mount the unit with the supplied screws.
Connect speakers
ilter frequency for subwoofer.
Note
Use speakers with an impedance of 2 to 8 ohm (4 to 8 ohm when used as a
bridged amplifier).
Match the "left", "right", "+" and "-" terminals correctly. Revised polarity may
degrade sound quality.
E
a
Left speaker
Л
Right speaker
П а
REMOTE
LEVEL CONTROL
SUB
WOOFER
SUBSONIC
ON OFF
30Hz
320Hz
White
Б
Б
White / Black
4 ohm speaker
Д а
4 О
b
REMOTE
LEVEL CONTROL
SUB
SUBSONIC
WOOFER
ON OFF
30Hz
320Hz
4 ohm speaker
4 ohm speaker
Д а
4 О
Д а
4 О
Option 1: Mono bridged mode: connect 1 speaker
Option 2: Stereo mode: connect 2 speakers
Connect car audio
E
Option 1: High level input connection
Connect the amplifier to your car audio with the supplied High level
input connector.
Option 2: Line input connection
b
Connect the amplifier to the car audio with a RCA cable (not supplied).
Connect power
F
1
Make the power connection as illustrated below:
Connect the ground wire from the car to the
Connect the remote wire from the car audio to the
With this connection, you can turn on/off the amplifier
with the car audio.
Connect the power wire from the car battery to the
Tip
If your car audio does not have remote output, connect the remote input
terminal (REM) to the accessory power supply.
4. Use your power amplifier
Adjust input level
D
You can adjust the input voltage from 0.3V to 6V.
1
Rotate INPUT LEVEL to adjust input voltage.
F
to a metal point of the car
К
а
Car audio unit
А
а
Remote output
В
а ДУ
Car audio unit
А
а
Grey
С
G
/
С
/
Grey / Black
REMOTE
LEVEL CONTROL
SUB
SUBSONIC
WOOFER
ON OFF
30Hz
320Hz
REMOTE
LEVEL CONTROL
Car audio unit
А
а
LINE OUT
Л
a
Adjust bass boost
b
You can punch extra bass for 0 to 12dB.
1
Rotate BASS BOOST to punch for extra bass.
a
About the protector indicator
The amplifier has a built-in protection circuit to protect the transistors
and speakers when:
The unit is overheated. Or
A DC current is generated. Or
The battery voltage is over low or over high. Or
The speaker terminals are short circuited.
When the PROTECT indicator lights up in red, the unit shuts down
automatically. If this happens, please:
GND socket.
1
Take out the disc or tape and turn off the car audio.
REM socket.
2
Check the cause of the malfunction (see above).
3
If the amplifier has overheated, wait until the unit cools down
+12V socket.
before use.
Adjust subwoofer frequency
Rotate Subwoofer to adjust low-pass-f ilter frequency for subwoofer.
1
Rotate SUBWOOFER to adjust frequency: 30Hz to 320Hz.
Turn subsonic f ilter on or off
1
Slide SUBSONIC to ON position.
The subsonic is turned on, frequency below 15Hz is f
To turn off the subsonic filter, slide
SUBSONIC ON/OFF to
OFF position.
а
а
less than 450 mm (18 in)
М
450
(18
)
Fuse (60 A)
П а
а
(60 А)
+12 V car battery
А
а
+12 В
H
Adjust volume
G
You can adjust volume at the front seat via the supplied volume control.
1
Connect the supplied volume controller to the REMOTE LEVEL
CONTROL socket.
2
Rotate the volume knob to adjust volume.
Replace fuse
H
If there is no power, the fuse may be damaged and need to be replaced.
1
Pull out the damaged fuse.
2
Replace the fuse with the supplied fuses or to buy two fuses
that matches the voltage of the damaged fuse (30Ax2).
If the fuse gets damaged immediately after it has been replaced, there
may be an internal malfunction. In such case, consult your Philips dealer.
5. Product information
Note
Product information is subject to change without prior notice.
Power Output (RMS)
- 4 ohm
250Wx1
- 2 ohm
400Wx1
Total harmonic distortion
0.08%
Signal to noise ratio
105dB
Frequency response
5-320Hz
iltered.
Input sensitivity
300mV-6V
Input impedance
22k ohm
Fuse rating
30Ax2
Dimensions (DxWxH)
54.4x336.5x240.2mm

Advertisement

Table of Contents

   Also See for Philips CMP100

   Related Manuals for Philips CMP100

   Summary of Contents for Philips CMP100

  • Page 1 Light in red when the PROTECTOR is activated. • Dimensions (DxWxH) 54.4x336.5x240.2mm Electronics N.V. or their respective owners. Philips reserves the right to change products at any time bridged amplifier). without being obliged to adjust earlier supplies accordingly. POWER •...
  • Page 2 аккумулятора к разъему +12 В. SUBWOOFER авторских прав. Компания Philips оставляет за собой право в любое время вносить изменения в you contact Philips, ensure that the apparatus is nearby and the model изделие без обязательств соответствующим образом изменять ранее поставленные изделия.

Comments to this Manuals

Symbols: 0
Latest comments: