About Slide Switch Operation; Turning Power On And Off; Detaching And Attaching The Monitor; How To Connect To A Bluetooth Compatible Device (Pairing) - Alpine EX-10 Owner's Manual

3
Closing the cover
Slide the cover as illustrated until a click is heard.
WARNING
DO NOT OPERATE ANY FUNCTION THAT
TAKES YOUR ATTENTION AWAY FROM SAFELY
DRIVING YOUR VEHICLE.
Any function that requires your prolonged attention should only be
performed after coming to a complete stop. Always stop the vehicle
in a safe location before performing these functions. Failure to do
so may result in an accident.

About Slide Switch Operation

Perform the LIST operation by moving the slide switch
on the right forward
Perform the SKIP operation by moving the slide switch
on the left forward ▼ or back ▲.
% SKIP ▲
% SKIP ▼
These switches are identified in this manual as follows.
Slide switch on the right: "the LIST switch"
Slide switch on the left: "the %SKIP switch"

Turning Power On and Off

Press the switch of monitor to turn on the unit.
Press and hold the switch of monitor for at least 2
seconds to turn off the unit.
• When an iPod is connected, the power is automatically turned on.
• If the unit is connected, and the power is turned on when the
cigarette lighter power is turned on, the battery continues to be
consumed. Depending on the vehicle, even if you turn off the engine,
the cigarette lighter power is not turned off, and if it is left turned on
for long time, the battery may be drained entirely. In this case,
disconnect the cigarette adapter. Also, activate the Automatic Power
OFF function. Refer to "Automatic Power OFF Function (Auto
Poweroff)" (page 15).
or back .
LIST
LIST

Detaching and Attaching the Monitor

For taking the monitor out of the car, refer to step 3 in "Installing the
Monitor" (page 19).
How to connect to a Bluetooth
compatible device (Pairing)
For details on the control from a Bluetooth compatible device, refer to
the Owner's Manual of the Bluetooth compatible device.
1
Press SETUP to activate the SETUP selection mode.
2
Slide the LIST switch in the direction of
select "Bluetooth," and then press
3
Press /ENTER.
The pairing mode is activated, and connection with a
Bluetooth compatible device is available.
4
Set a Bluetooth connection from a Bluetooth
compatible device.
5
The PIN code (Initial setting "0000") is displayed on
this unit.
6
Input the PIN code in a Bluetooth compatible device.
7
If this unit is successfully connected to a Bluetooth
compatible device, a paired device name is
displayed on the unit.
• For mobile phone pass code (PIN code) input operation, refer to the
mobile's Owner's Manual.
• The PIN code (pass code) can be set. Refer to "Setting the PIN Code
(Pass Code)" (page 14).
• If a device name is not displayed when a mobile phone is connected,
Phone1 to 5 is displayed; when an audio device is connected, Audio1
to 5 is displayed; phone/audio is connected, Device1 to 5 is
displayed.
• You can connect (pair) up to 5 Bluetooth compatible mobile phones
th
or audio devices. When a 6 phone or device is connected, the least
used device is automatically disconnected.
• If the unit cannot be connected to a Bluetooth compatible device,
"Pairing Failed" is displayed for 2 seconds.

About Sound Output of the Unit

Sound of the unit is output using the FM transmitter function, which
transmits sound to the FM car radio by radio signals, or via an audio
output terminal. Set sound output in "Setting Sound Output (Output
Mode)" (page 15).
If sound is output from the FM radio, refer to "FM Transmitter Function
(Frequency)" (page 13), and adjust the frequency accordingly.
When the hands-free phone function is used, you can select whether
sound is output from the built-in speaker of the unit. Refer to "Setting
the Telephone Voice Output (HFP Speaker)" (page 14).
to
/ENTER.
5
-EN