Related Manuals for Fujitsu TSC SK-TSC-1125S
Summary of Contents for Fujitsu TSC SK-TSC-1125S
- Page 1 Fujitsu Microelectronics Europe FMEMCU-UG-010003-11 User Guide FMA1125 TOUCH SENSOR CONTROLLER SK-TSC-1125S QUICK START GUIDE...
-
Page 2: Revision History
V1.1, CHa, disclaimer updated, some corrections This document contains 19 pages NOTE: The FMA1125 touch sensor controller is developed and owned by ATLab Inc., South Korea, and is distributed by Fujitsu Microelectronics Europe. SK-TSC-1125S User Guide Issue - 2 -... -
Page 3: Warranty And Disclaimer
The use of the deliverables (e.g. software, application examples, target boards, evaluation boards, starter kits, schematics, engineering samples of IC’s etc.) is subject to the conditions of Fujitsu Microelectronics Europe GmbH (“FME”) as set out in (i) the terms of the License Agreement and/or the Sale and Purchase Agreement under which agreements the Product has been delivered, (ii) the technical descriptions and (iii) all accompanying written materials. -
Page 4: Table Of Contents
3 BASIC TUNING PROCESS USING THE COMMAND LINE INTERFACE AND A PC TERMINAL PROGRAM ... 13 4 RELATED PRODUCTS ... 16 5 INFORMATION IN THE WWW ... 17 6 CHINA ROHS REGULATION... 18 7 RECYCLING ... 19 SK-TSC-1125S User Guide - 4 - © Fujitsu Microelectronics Europe GmbH... -
Page 5: Overview
(e.g. tuning with command line interface). Of course the Starter Kit itself can also be used with different host software and / or hardware combinations. This evaluation system must only be used for test applications in an evaluation laboratory environment! © Fujitsu Microelectronics Europe GmbH SK-TSC-1125S User Guide - 5 -... -
Page 6: Features
When the LCD is present, depending on the application, some information will be displayed, such as the distribution of the touch strength among the input channels. The same information can also be obtained by the terminal program interface. SK-TSC-1125S User Guide - 6 - © Fujitsu Microelectronics Europe GmbH... -
Page 7: Installation
USB drivers, the Softune Workbench and the EUROSCOPE debugging environment. The example firmware can be programmed using the Flash programmer which can also be found on the same CD. © Fujitsu Microelectronics Europe GmbH SK-TSC-1125S User Guide - 7 -... -
Page 8: Setup (Pc Software)
Generally, the command line can be accessed by any PC terminal program. However, not all terminal programs support the ‘form feed’ command to clear the screen; this is used for the real-time monitoring modes. Therefore the Fujitsu ‘SK Wizard’ is recommended for tuning; it can be downloaded free of charge at http://mcu.emea.fujitsu.com/mcu_tool/software.htm... - Page 9 SK-TSC-1125S User Guide Figure 2: System set-up (LCD and SK-16FX EUROSCOPE not included!) © Fujitsu Microelectronics Europe GmbH - 9 -...
-
Page 10: Jumper Settings
GINT connected to X1 Chip ID = 0x68 Chip ID = 0x69 Clock can be provided by test pin TP1 TCLK pin connected to GND Internal LDO not connected Internal logic supplied by internal LDO - 10 - © Fujitsu Microelectronics Europe GmbH... -
Page 11: Ada-16Fx-Tsc-Lcd
SK-16FX-EUROSCOPE for configuration options. Note: The TSC can operate at 3.3V as well as 5V (default), but most standard LC displays will only operate at 5V. © Fujitsu Microelectronics Europe GmbH SK-TSC-1125S User Guide Description I2C SCL line not connected to Pull-up resistor... -
Page 12: I2C Header (X1) Pinout (Ada-16Fx-Tsc-Lcd)
‘Beep’ Signal for Piezo Buzzer X3 Pin 7 X3 Pin 8 X4 Pin 1 X4 Pin 2 - 12 - © Fujitsu Microelectronics Europe GmbH Descripton I2C Serial Clock Line I2C Serial Data Line System Ground (FMA1127-40N only) Reset Pin of TSC... -
Page 13: Basic Tuning Process Using The Command Line Interface And A Pc Terminal Program
Here for, only a terminal program is needed on the PC, so it is platform independent. The Fujitsu Startkerkit Wizard is recommended for this, as it supports the ‘Form Feed’ command which is used for the monitoring modes explained later in this document. - Page 14 Up to 10 register settings (all read/writable registers) can be stored to and loaded from the internal Flash memory of the Microcontroller using the ‘stp’ and ‘ldp’ commands. Please refer to the application note ‘FMA1125_Init_Reg_Description’ for further register description. - 14 - © Fujitsu Microelectronics Europe GmbH...
- Page 15 SK-TSC-1125S User Guide Figure 3: Monitor Mode (‚mon2’) In mon2 mode, channels with active touch status will be shown with stars ‘*’, those in inactive state are shown with lines ‘|’. © Fujitsu Microelectronics Europe GmbH - 15 -...
-
Page 16: Related Products
4 Related Products < SK-16FX-EUROSCOPE < SK-TSC-1127-SB SK-TSC-1125S User Guide Evaluation board for the 16FX Family MB96340 Series Starter Kit for the FMA1127 Touch Sensor Controller with 12 channels - 16 - © Fujitsu Microelectronics Europe GmbH... -
Page 17: Information In The Www
5 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: Touch sensor controllers: http://www.fujitsu.com/emea/services/microelectronics/tsc/ Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://mcu.emea.fujitsu.com/ Linear Products: Power Management, A/D and D/A Converters http://www.fme.fujitsu.com/products/linear/start.html... -
Page 18: China Rohs Regulation
SK-TSC-1125S User Guide 6 China RoHS regulation This starter kit is compliant with China RoHS - 18 - © Fujitsu Microelectronics Europe GmbH... -
Page 19: Recycling
According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a D-63225 Langen GERMANY -- END -- © Fujitsu Microelectronics Europe GmbH - 19 -...