PORTABLE CELLULAR TELEPHONE SCH-620 SERVICE Manual PORTABLE CELLULAR TELEPHONE CONTENTS 1. General Introduction 2. Specification 3. Installation 4. NAM Programming 5. Product Support Tools O K/ M EN U 6. Troubleshooting E N D / C LR S E N D...
Page 2
• IS-126 : Mobile Station Loopback Service Options Standard SCH-620 is composed of main handset, rapid charger, three batteries (1600 mAh, 1000 mAh, 550mAh), hands- free kit, car adaptor, and travel charger. Hands-Free Kit is designed to be operated in full-duplex mode taking turn-around delay between the phone and the system into account.
Standby Time Talk Time slim battery up to 75 hours up to 90 min standard battery up to 155 hours up to 200 min extended battery up to 250 hours up to 330 min SAMSUNG Proprietary-Contents may change without notice...
-61 dBm Test1: ±24 dB or less Test2: 0 mS ~ 2.5 mS Colsed Loop Tx Power Control Range Test3: ±24 dB or more Test4: ±24 dB or more Test5: ±24 dB or more SAMSUNG Proprietary-Contents may change without notice...
Page 5
63 +10 LOG (PY) dB f0+45KHz ~ f0+60KHz (where f0=carrier frequency f0+60KHz ~ f0+90KHz PY=mean output power in watts) f0+90KHz ~ 2f0 below 43 + 10 LOG (PY) dB Harmonic and conducted Spurious Emissions SAMSUNG Proprietary-Contents may change without notice...
Page 7
9 : TEx : Tx vocoder rate (8 is full rate, 1 is 1/8th rate) E : EVRC V : 13k or 8k 10 : REx : Rx vocoder rate (8 is full rate, 1 is 1/8th rate) 11 : xx : Walsh code used in traffic channel SAMSUNG Proprietary-Contents may change without notice...
3. To remove the battery pack, release it by pressing the button on the rear of the phone. 4. Slide the battery pack downward about 1cm (1/2inch and lift it away from the phone. Press this button to release the battery pack SAMSUNG Proprietary-Contents may change without notice...
Page 9
GH43-00132D SPECIFICATIONS USING “DTC 61AB” Product Charging time (hours) Stand by time (hours) Talking time(min) Front Rear Digital Digital Slim Battery Pack (Li-ion: 500mAh) Standard Battery Pack (Li-ion: 1000mAh) Extended Battery Pack (Li-ion: 1600mAh) SAMSUNG Proprietary-Contents may change without notice...
Page 10
3-3-2 Hands-Free Box 1. Drill holes in a proper location for the hands-free box, attach the mounting bracket by using the screws. See the figure 3-3. 2. Install the hands-free box into the bracket. SAMSUNG Proprietary-Contents may change without notice...
Page 11
Normal place is the sun visor. 2. Once the microphone has been correctly positioned, connect the microphone wire to the MIC jack on the hands-free box. MOUNTING BRACKET Figure 3-3 Hands-Free Box 1 Installation SAMSUNG Proprietary-Contents may change without notice...
Page 12
Make sure the fuse having a proper capacity is used on the power cable. Make sure the cables do not pass over any sharp metal edge that may damage it. Micro Phone Yellow(Ignition) White(Stereo Mute) Red(Vehicle Battery) Black(GND) SAMSUNG Proprietary-Contents may change without notice...
-stores it. Slot Index -Slot mode index. The higher, the longer sleeping time to change, enter new one. -stores it. Pref NAM1... -Preferred system selection for NAM1 Digital pref changes the system. -stores it. SAMSUNG Proprietary-Contents may change without notice...
Page 14
Acquisition system ID 1, Current status is displayed. ID number - to change, enter new one. - store it. FM Acq SID2 Acquisition system ID 2, Current status is displayed. ID number - to change, enter new one. - store it. SAMSUNG Proprietary-Contents may change without notice...
- changes the status ‘YES’ to enable, ‘NO’ to disable - store it. FM pref A only Preferred system selection, current status is displayed. * or # - changes the status - store it. SAMSUNG Proprietary-Contents may change without notice...
Page 16
ID number - to change, enter new one. - stores it. CD Acq SID 2 2nd Acquisition system ID, current status is displayed. ID number - to change, enter new one. - stores it. SAMSUNG Proprietary-Contents may change without notice...
Page 17
CDMA foreign SID, current status is displayed. * or # - changes the system. - stores it. CDMA fNID CDMA foreign NID, current status is displayed. * or # - changes the system. - stores it. SAMSUNG Proprietary-Contents may change without notice...
Page 18
LCD return to the NAM1 setup mode. 1:Phone # 2.FM 2:CDMA 4-3 Setting Up NAM2 LCD Display Key in Function NAM Program -Choose ‘Setup NAM2’ 1:General 2:Setup NAM1 3:Setup NAM2 The NAM2 setup program is the same as ‘NAM1’. SAMSUNG Proprietary-Contents may change without notice...
Page 19
-changes the status. -store it. 2. Setting Up NAM2 LCD Display Key in Function NAM Program -Choose ‘Setup NAM2’ 1:Setup NAM1 2:Setup NAM2 The Quick NAM2 setup is the same as ‘1. Setting up Quick NAM1’ SAMSUNG Proprietary-Contents may change without notice...
Page 20
Slot Mode Slot mode ‘Yes’indicates the slot mode. or # -changes the status. -store it. General Slot Index Slot mode index. The higher, the Ionger sleeping time -to change, enter new one. -store it. SAMSUNG Proprietary-Contents may change without notice...
Page 21
CDMA Home SID CDMA Home System ID, current status is displayed or # -change the status. -store it. NAM1 Digital CDMA fSID CDMA foreign SID, current status is displyed or # -change the system -store it. SAMSUNG Proprietary-Contents may change without notice...
Page 22
-store it. 5. Setting Up NAM2 LCD Display Key in Function NAM Program -Choose ‘Setup NAM2’ 1:Setup NAM1 2:Setup NAM2 The Quick NAM2 setup is the same as ‘4. Setting up Quick NAM1’ SAMSUNG Proprietary-Contents may change without notice 4-10...
IMPORTANT INFORMATION Purpose The Product Support Tool (PST) offers you the ability to interface with the SAMSUNG CDMA telephone using a PC. With this tool you can program the phones network system requirements and functionality, swap phone data, and download software upgrades. This document supports UniPST version 1.xx.
Page 24
The Main Menu Screen shows the basic tasks that are available. CAUTION: DO NOT attempt to program phone with a low battery. PST SETUP UniPst supports SAMSUNG CDMA portable telephone. You can select serial port COM1 or COM2. 5-2-2 Operation Procedure Service Programming The Service Programming screens enable you to set and change the service activation parameters of the phones.
Page 25
3.Click Mode Select box, then Select SERVICE MODE?to return to the Service Mode Screen. NOTE: DO NOT POWER OFF WHILE THE PHONE IS BEING DOWNLOADED! SAMSUNG Proprietary-Contents may change without notice...
CAUTION : Because there is the loss (0.33V at Max Power) of the test jig and Data cable, you’d better input 3.93V to the DC Power Supply to use 3.6V (Battery normal voltage) at Cellular phone Items needed to purchase from SAMSUNG ITEMS...
CONNECT TO HP SERIAL PORT A-OUT A-IN PROBE NOT USED CONNECT TO CONNECT TO AUDIO OUT PORT OF AUDIO IN PORT OF TEST EQUIPMENT TEST EQUIPMENT (USE BNC CABLE) (USE BNC CABLE) TEST CABLE SAMSUNG Proprietary-Contents may change without notice...
Page 28
Dsub 25 PIN CONNECTOR PIN DESCRIPTION (TEST CABLE 1, BACK SIDE) DATA DESCRIPTION Dsub CONN. DATA DESCRIPTION Dsub CONN. PIN NO. PIN NO. 12,21 DP_RX_DATA DGND 2,4,6,13,19 HP_PWR BATT 15,16,22 3,20 TX_AUDIO DP_TX_DATA RX_AUDIO SAMSUNG Proprietary-Contents may change without notice...
Page 29
F. “7 2 2 7 5 #” : Output RF power level setting. “275” means AGC level and AGC level range is from 0 to 511. G. “1 0 2” : RF Power level control, 2(0~7) means power level . SAMSUNG Proprietary-Contents may change without notice...
TX Control data VOLUME_UP Electric Volume Up VOLUME_DOWN Electric Volume Down VOC_CDMA_UNITY_GAIN Vocoder CDMA unity gain VOC_FM_HFRX_UPGAIN Vocoder fm hfrx upgain DTMFON turn on DTMF DTMFOFF turn off DTMF COMPANDORON turn on compandor SAMSUNG Proprietary-Contents may change without notice...
Page 31
READ_TEMP read a TEMP RXRAS_AUTO adj RXRAS from 8924C JOJ_98.06.20 BUZZER_ON Buzzer on BUZZER_OFF Buzzer off VOC_PCMLPON turn on to play a PCM LOOP BACK VOC_PCMLPOFF turn off to play a PCM LOOP BACK SAMSUNG Proprietary-Contents may change without notice...
Page 32
CDTRK_ADJ CDMA TRK LOCAL ADJUST TXRAS_ADJ TX RAS adj = TXRAS offset arry RXRAS_ADJ RX RAS adj = RXRAS offset arry HW_CHANFLAT SW_CHANFLAT CH_FLATNESS FM_TX_PWR setting the volume for power Level 2-7 TEMP SAMSUNG Proprietary-Contents may change without notice 5-10...
Q203 pin 4. Check U210 and its neighboring U210 pin 1 input circuits. =3.6V? Check U210 and its neighboring U210 pin 5 output circuits. =3.0V? Check U206 and its neighboring U206 pin 5 output circuits. =3.0V? SAMSUNG Proprietary-Contents may change without notice...
Page 34
Check ‘H’ level input U304 pin 38. from U304 pin 38? Check the LED and its neighboring LED ON? circuit. Replace if required. Check the LCD pins and its Normal initial neighboring circuit. display on LCD? Replace if required. SAMSUNG Proprietary-Contents may change without notice...
Page 35
U104 pin 7L? Check U209 and its ‘H’ level input from neighboring circuits. U104 pin7L drive U209? Replace if required Check Q206, L202 The voltage applied to and its neighboring circuits. LCD(U207) pins31? Backlight LED on SAMSUNG Proprietary-Contents may change without notice...
Page 36
U104, pins 5C, 48, 5C, 48, 5D, 4A, 6C, 5A, 6D 5D, 4A, 6C, 5A, 6D? Check U104 pins 2A, 4C, and 3B Check CON102-24. Normal key data input? Replace the keypad assembly SAMSUNG Proprietary-Contents may change without notice...
Page 37
CHIP_CELECT U104 pin 7M Replace if required. Check Q201,Q202,R227,R220, CLK waveform applied and D206.Replace if required. to CON102-24 pin 24? Is the buzzer Connect the buzzer correcty connection correct? Check the buzzer and replace if required SAMSUNG Proprietary-Contents may change without notice...
Check U406 969.27MHz Tx IF level local Input level CH:363 SPAN 5MHz CDMA: -15dBm CDMA: -8dBm Tx VCO:270.76MHz IF:130.38MHz Check Tx Check U404 Check U306 Power level. Out level. Out level CDMA: -12dBm CDMA: +8.63dBm SAMSUNG Proprietary-Contents may change without notice...
Page 39
Check IF filter in/output OK? solderling CDMA : -16dBm FM : -6dB Check 2nd Check IFR(U304) local & AGC control Soldering voltage OK? 170.76MHz170.76MHz RF Rx FM OK IFR INPUT CDMA :-40dBm FM : -26dBm SAMSUNG Proprietary-Contents may change without notice...
Page 40
Troubleshooting 6-4 CDMA Receiver Section Start CDMA mode Normal CDMA Check CDMA RX path SVC & ROAM OK? Setup CDMA Check Transmitter call. OK? Measure CDMA FER Normal CDMA RF? SAMSUNG Proprietary-Contents may change without notice...
Page 41
Check C22. Voltage of Check U25. (about 4.5V) C41.(5V) Check U26. Check Voltage of Check C22. LD1, LD2 (about 4.5V) LED blink? Check component the secondary (RED>GRN>YEL) D30, D20, U22, U23, U24, U25, U26. SAMSUNG Proprietary-Contents may change without notice...
Page 42
In conversation mode, volume Full Charging check adijustment, mute on/off, calibration check Auto power off Charging LED Check according to lgnition status Handsfree off with the phone powered off or removed SAMSUNG Proprietary-Contents may change without notice 6-10...
Page 43
7. Exploded View and its Parts List 7-1 Cellular phone Exploded View 10-1 10-2 10-3 15-1 10-4 15-2 SAMSUNG Proprietary-Contents may change without notice...
Page 45
Exploded view and its Part List 7-3 Desk-Top Rapid charger Exploded View TYPE SEC. CODE Remark GH44-00063A Israel GH44-00063B Hong Kong Description Q’TY Case. upper Hook-plate SCREW Battery housing SCREW Power cord Case. Lower SCREW BUM PON Label SAMSUNG Proprietary-Contents may change without notice...
Page 46
Exploded view and its Part List 7-4 Hands-free Kit 1 Exploded View Description Q’TY Case. upper SCREW 3 5Y Case. Lower SCREW 3 12Y Sponge Label SAMSUNG Proprietary-Contents may change without notice...
Page 47
Exploded view and its Part List 7-5 Speaker Exploded View Description Q’TY Case. Front Speaker Case. Rear Bolt HEX. NUT Hamdle Speaker wire Screw Label SAMSUNG Proprietary-Contents may change without notice...
Page 48
Exploded view and its Part List 7-6 Cradle Exploded View Description Q’TY Cover Top Holder Socket Spring Lock Locker Locker Eject-A Eject Spring Frame Eject-B Screw SCREW Cover Bottom Screw Label I/F coil cord Data coil cord SAMSUNG Proprietary-Contents may change without notice...
Page 67
CONTROL BOX CASE SCREW CONTROL BOX CASE CABLE MIC #2 PS 3x6 Y CUSHION MIC. #2 PS 3x12 B MIC CONDENSOR MICROPHONE CABLE POWER MICROPHONE LABEL MICROPHONE LABEL #1 FT 2x8 B LABEL 1P+1SCHIELD SAMSUNG Proprietary-Contents may change without notice 8-19...
SEMI-FIXEED RES RG06P102 L1, 2 INDUCCTOR PTF1 SGH500 TRANS SCH500 CHOKE ASS'Y R4, 5 SURGE RESISTOR PPSR0.5W C1, 2 CAP EL SHL400V10UF CAP EL KMF16V330UF CAP EL AG10V1000UF C4, 20, 24 CAP EL 1SK1C476M05007 SAMSUNG Proprietary-Contents may change without notice 8-23...
Page 72
PIC16C711 P.C.B TC30 AC PLUG ASS'Y PLUG TERMINAL CONTACT TERMINAL CONTACT TERMINAL CASE BOTTOM CASE TOP SCREW SCREW OUTPUT CABLE ASS'Y AXR324100201 LABEL CARTON BOX MAIN BOARD CARD BOARD(A) CARD BOARD(B) VINYL SACK SAMSUNG Proprietary-Contents may change without notice 8-24...
Page 73
UPPER COVER V. RESISTOR FR-4 (T=1.6) LOWER COVER 1.68PIE/25MM FUSE COVER PC/BLACK OUTER SPRING PC/BLACK POWER CONTACT PC/BLACK SPRING CLA OUTER SPRING FUSE HOLDER CLA POWER CONTACT FUSE PLATE UPPER+LOWER FUSE HOLDER/CLA FUSE PLATE/CLA SAMSUNG Proprietary-Contents may change without notice 8-25...
Page 74
Electrical Parts List Design LOC DESCRIPTIONS SEC CODE REMARKS HANISHELLL +PH (2.6x14-2S) BLACK OUT BOX CLA010A CURRUGATED PAD PACKING ASS’Y CLA SPONGE TAPPING SCREW NAME LABEL CARTON BOX CLA CORRUGATED PAD SAMSUNG Proprietary-Contents may change without notice 8-26...
Need help?
Do you have a question about the SCH-620 and is the answer not in the manual?
Questions and answers