Table of Contents
Advertisement
Drying Tumblers
NOTA: Para bajar una
copia de estas
instrucciones en
español, visite
www.comlaundry.com.
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
50 Pound Capacity
75 Pound Capacity
Refer to Page 3 for Model Identification
www.comlaundry.com
Part No. M414904R8
August 2007
Advertisement
Table of Contents
Related Manuals for Alliance Laundry Systems M414904R8
Summary of Contents for Alliance Laundry Systems M414904R8
- Page 1 Refer to Page 3 for Model Identification NOTA: Para bajar una copia de estas instrucciones en español, visite www.comlaundry.com. Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. M414904R8 www.comlaundry.com August 2007...
- Page 3 These instructions must be posted in a prominent location. Step-by-step instructions of the above safety information must be posted in a prominent location near the tumbler for customer use. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 4: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M414904... -
Page 5: Introduction
QT – dual digital timer ZX – NetMaster network, prep for coin CY – prep for card RM – reversing OPL Micro ZY – NetMaster network, prep for card M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 6: Customer Service
Models starting Serial No. 0309____ or later will have the wiring diagram part number in the lower portion of the electrical data on the serial plate. TMB803N TMB803N Serial Plate Figure 1 M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 7: Safety Information
NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 8: Important Safety Instructions
12. Always clean the lint filter daily. 13. Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint, dust and dirt. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 9 W055 28. DO NOT operate the tumbler if it is smoking, grinding, has missing or broken parts. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 10: Operating Instructions
DOES NOT remove all electrical power from machine. Step 4: Remove Laundry When the cycle is complete, open door and remove the laundry. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 11: Control Instructions
3. Press the PUSH TO START button and hold it for approximately three (3) seconds. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 12: Manual Timer Control
4. Select reversing or nonreversing cylinder rotation setting, if applicable. 5. Press the PUSH TO START button in and hold it in for approximately three seconds. This starts the tumbler cycle. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 13: Dual Digital Timer Control
The intermittent tumbling will continue for one hour or until the door is opened. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 14: Error Codes
Airflow switch closed when cycle ● AF - 1 started Check airflow switch. Replace if inoperative. ● Airflow switch failed to close after AF - 2 cycle started M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 15: Electronic Opl Control
The intermittent tumbling will continue for one hour or until the door is opened. TMB806N TMB806N Figure 8 2. Select reversing or nonreversing cylinder rotation setting, if applicable. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 16: Reversing Operation
If the cylinder is turning counterclockwise when switched to nonreversing, it will continue for a few seconds and then start up in the proper direction. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 17: Single Drop Control
Run Mode once power is restored and continue the cycle. If a power disruption is more than 5 seconds, with a cycle in process, the control will enter Start Mode once power is restored. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 18 W002 Display Definition Corrective Action Check airflow switch. Replace if inoperative. ● Airflow switch opened/closed 5 or AF (flashing) more times in a running cycle. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 19: Mdc Coin Control
4. When the cycle is complete, open door and or DELICATES by pressing the appropriate remove the laundry. temperature pad. 2. Insert the coin(s) in the coin slot. 3. Press START pad to start tumbler. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 20: Mdc Card Control
4. When the cycle is complete, open door and or DELICATES by pressing the appropriate remove the laundry. temperature pad. 2. Insert card into opening. 3. Press START pad to start tumbler. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 21: Netmaster Coin Control
NO HEAT by pressing the appropriate remove the laundry. temperature pad. 2. Insert the coin(s) in the coin slot. 3. Press START pad to start tumbler. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 22: Netmaster Card Control
2. Insert card into opening. DO NOT remove the card until “REMOVE CARD” LED is lit. 3. Press START pad to start tumbler. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 23: Ignition Control Operation
Lockout Mode again. ignition. If the three attempts at ignition fail, the ignition control will enter Lockout Mode. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 24 Reset Switch is Shorted Slow Red and Green Flashes Low Voltage Detection Fast Red and Orange Flashes Ignition Control is in Reset Delay TMB2176N Diagnostic (DGN) LED Figure 14 M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 25: Maintenance
Be sure that it does so. Excessive gaps between the lint screen and the lint screen panel allow lint to pass into the ductwork system and may restrict airflow. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 26: Monthly
3. Check and clean steam coils, if applicable. 4. Check flow of combustion and ventilation air. 5. Check belt tension and condition. Replace worn or cracked belts. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 27: Daily Maintenance
Lint buildup will act as an insulator, causing machine to overheat. Clean lint and debris buildup from blower to maintain proper airflow, to avoid overheating and prevent possible vibration. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 28 Check cylinder and front panel seals. Inspect cabinet and inner panels for any damage, replace or repair as needed. Clean burner tubes of any lint buildup. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 29: Before You Call For Service
Alliance Laundry Systems at (920) 748-3950 for the name and address of the nearest authorized parts distributor. For technical assistance, call (920) 748-3121. M414904 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Need help?
Do you have a question about the M414904R8 and is the answer not in the manual?
Questions and answers