Page 1
INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION WOOD HINGED PATIO DOOR – (INCLUDES – STANDARD, PERFORMANCE UPGRADE AND HURRICANESHEILD® IMPACT RESISTANT IN-SWING, OUT-SWING) Important Safety Information: These instructions are not to be used with any other construction method. IMPORTANT NOTICE: REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.
Page 2
YOU WILL NEED TO SUPPLY: TOOLS REQUIRED: INSTALLATION CLIP OPTION:...
ROUGH OPENING PREPARATION Confi rm the opening is plumb and level. Confi rm the door will fi t the opening. Cut the water resistive barrier. Fold the water resistive barrier. For Doors Using Optional Sill Pan Go To Step 1I. Apply sill fl...
Page 4
Optional Sill Pan Instructions. Cut the sill pan Make a 1" cut in each fold 1 " IN T E R IO R SI LL 1 " PA N LI P V a ri a b le E X T E R IO R SI LL P A N LI P 1 "...
Attach the aluminum sill support or wood I N T E R I O R S I L L P A N L I P E X T E R I O R S I L L P A N L I PREPARE THE DOOR FOR INSTALLATION TWO OR MORE PEOPLE WILL BE REQUIRED TO HANDLE THE PANEL AND FRAME SAFELY.
#6 x 5/8” corrosion Doors using Installation Clips: resistant screws 6“ from end SETTING AND FASTENING THE DOOR Place three 3/8" beads of sealant. 1 st B e a d 2 n d B e a d 6” L e a v e a 2 " b re a k in ce n te r o f I N T E R I O...
Page 7
Plumb and square door. Check the interior reveal. Fasten the door to opening 16d galvanized finishing nails E x t e r i o Carefully open the door(s) Double door with Center Latch: For Out-Swing Standard Installation Applications Only: Install sill screws. SILL SCREWS FOR ARCHITECT SERIES PERFORMANCE UPGRADE AND DOORS WITH HURRICANESHIELD IMPACT-RESISTANT GLASS ARE INSTALLED IN STEP 5.
Page 8
Shim between the frame and the rough opening at the head strike location and at every frame anchor hole location. I n t e r i o On each hinge, starting at the top, Check door operation. Doors WITHOUT adjustable hinges: Adjustable Non-Adjustable Hinge...
For Doors with adjustable hinges: On doors with a lock strike in the Head side, ~8” INTEGRATING THE DOOR TO THE WATER RESISTIVE BARRIER Apply a corner bead of sealant at the point Install the head fl ashing. Apply a piece of fl ashing tape Fold down the top fl...
Page 10
INSTALL THE PERFORMANCE UPGRADE OR HURRICANESHIELD FASTENERS Frame Screw Method: 6" 16" MAX O.C. 6" 6" 16" MAX O.C. 6" Jambs: Out-swing: Clearance Clearance Hole Hole Location Location Clearance Clearance In-swing: Open door panels; Hole Hole Location Location 6" 16" MAX O.C. 6"...
Page 11
Secure the jambs and head of the door. DO NOT DO NOT Drill 13/64" clearance holes through the threshold Installation Clip Method: Fasten the door to the opening by driving two #8 x 1-1/4” Frame Screw and Installation Clip Methods: Drive #10 x 3-1/2”...
INTERIOR SEAL Add a sealant bead across the inner sill and 6" up each jamb Apply insulating foam sealant. 6 " Check the door operation by opening and closing the door. SEALING THE DOOR TO THE EXTERIOR WALL CLADDING VINYL/STEEL BRICK VENEER SIDING Backer Rod and...
Page 13
Insert backer rod Apply a bead of sealant Shape, tool and clean excess sealant. Remove plastic guards at the base of the door Install the hardware. INTERIOR FINISHING DO NOT BE CAREFUL NOT TO SCRATCH THE GLASS. EXTERIOR FINISHING...
DO NOT Pella makes no warranty of any kind and assumes no responsibility for Pella windows and doors installed in barrier wall systems. In the states listed above, the installation of Pella products in barrier wall or similar systems must be in accordance with Pella installation instructions.