1. Manuals
  2. Brands
  3. Pella Manuals
  4. Door
  5. 80JJ0103
  6. Installation instructions manual

Pella 80JJ0103 Installation Instructions Manual

Clad hinged patio door with adjustable hinges
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
©2008 Pella Corporation
INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION
FOR CLAD HINGED PATIO DOOR WITH ADJUSTABLE HINGES
PARA LA PUERTA PARA PATIO REVESTIDA, CON BISAGRAS ADJUSTABLES
Always read the Pella
installing this product, you are acknowledging that this Limited Warranty is part of the terms of the
sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella
product warranty. See Limited Warranty for complete details at http://warranty.pella.com.
These instructions were developed and tested for use with typical wood frame wall construction in
a wall system designed to manage water. These instructions are not to be used with any other
construction method. Installation instructions for use with other construction methods, multiple
units or bow and bay windows, may be obtained from Pella Corporation or a local Pella retailer,
or by visiting http://www.pella.com. Building designs, construction methods, building materials,
and site conditions unique to your project may require an installation method different from
these instructions and additional care. Determining the appropriate installation method is the
responsibility of you, your architect, or construction professional.
®
Limited Warranty before purchasing or installing Pella products. By
Part Number: 80JJ0103

Advertisement

Table of Contents
loading

Related Manuals for Pella 80JJ0103

Summary of Contents for Pella 80JJ0103

  • Page 1 These instructions are not to be used with any other construction method. Installation instructions for use with other construction methods, multiple units or bow and bay windows, may be obtained from Pella Corporation or a local Pella retailer, or by visiting http://www.pella.com. Building designs, construction methods, building materials, and site conditions unique to your project may require an installation method different from these instructions and additional care.

  • Page 2: Rough Opening Preparation

    YOU WILL NEED TO SUPPLY: TOOLS REQUIRED: ® ™ SmartFlash foil backed butyl window and door flashing tape or equivalent ™ Window and Door Insulating Foam Sealant by the Dow Chemical Company or equivalent low pressure polyurethane window and door foam - DO REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.

  • Page 3: Setting And Fastening The Door

    E. Apply sill flashing tape #1. Cut a piece of flashing tape 12" longer than the opening width. Apply at the bottom of the Note: The tape is cut 12" longer than the width so that it will extend 6" up each side of the opening. F.
  • Page 4 E. Plumb and square door. Place shims at each hinge and lock strike location between the door and the sides of the opening. bottom of the door to square it in the opening. Make sure that the panels are even across the bottom. Note: On center latch double doors the lock strike will not be shimmed since it is located in the center of the unit.

  • Page 5: Integrating The Door To The Water Resistive Barrier

    L. Check door operation. Open and close the door to check for proper operation. Make sure the door will latch correctly. Note: If there are any problems with the operation, recheck and adjust the reveal. M. Adjust the reveal if needed. The door panels have adjustable hinge increase the space between the hinge side of the frame and the door panel, or counter clockwise to increase the space between the door panel and the lock side of the frame.

  • Page 6: Interior Seal

    B. Apply top flashing tape. Cut a piece of flashing tape long least 1" past the side flashing tape on both sides. Apply the tape 1/2" onto the frame cladding, over the top Note: The top flashing tape must overlap the side flashing tape to prevent water from getting behind it.

  • Page 7: Sealing The Door To The Exterior Wall Cladding

    SEALING THE DOOR TO THE EXTERIOR WALL CLADDING When applying siding, brick veneer or other exterior finish material, leave adequate space between the door frame and the material for sealant. Refer to the illustration that corresponds to your finish material. Note: The sealant details shown are standard recommendations from the sealant industry.

  • Page 8: Exterior Finish

    The determination of the suitability of all building components, including the use of Pella products, as well as the design and installation of flashing and sealing systems are the responsibility of the Buyer or User, the architect, contractor, installer, or other construction professional and are not the responsibility of Pella.

Table of Contents