Cleaning Recommendations; Wall Mount - Braun Oral-B TRIUMPH 500 User Manual

Pressure sensor
If you put excessive pressure on your teeth, the
red pressure sensor light (b) will light up (picture 3,
page 3). Additionally, when brushing in Daily Clean
or Deep Clean mode, the brushing mode will change
to the «Sensitive» mode. Periodically check the
operation of the pressure sensor by pressing mode-
rately on the brush head during use.
Brushing modes
Your toothbrush offers different brushing modes:
«Daily Clean» – Standard mode for daily
«Deep Clean» – Mouth cleaning with
«Sensitive» – Gentle, yet thorough cleaning
«Whitening» – Polishing for occasional or
«Massage» – Gentle massage of gums
Your toothbrush automatically starts in the «Daily
Clean» mode. To switch to the other modes, succes-
sively press the mode button (picture 4, page 3).
To return from any mode back to the «Daily Clean»
mode, press and hold the mode button.
The brushing mode is memorized even when the
handle is briefly switched off during brushing. When
pausing longer than 30 seconds or briefly pressing
the mode button (d) during pause the brushing
mode resets to the «Daily Clean» mode.
Brush heads
Oral-B offers you a variety of different brush heads
that fit your Oral-B Triumph toothbrush.
Oral-B FlossAction
features micropulse bristles that allow
for an outstanding plaque removal in
the interdental areas.
Oral-B ProWhite
features a special polishing cup to
naturally whiten your teeth. Please
note that children under 12 years old
should not use the Oral-B ProWhite
brush head.
Both brush heads feature light blue INDICATOR
bristles to help you monitor brush head replacement
need. With thorough brushing, twice a day for two
minutes, the blue color will fade halfway down
10
mouth cleaning
extended brushing time of
45 seconds per quadrant
(3 minute total brushing time)
for sensitive areas
everyday use
approximately in a 3-month period. If the bristles
splay before the colour recedes, you may exert too
much pressure on teeth and gums.
We do not recommend using the Oral-B FlossAction
or Oral-B ProWhite brush head with braces. You
may use the Oral-B Ortho brush head, specifically
designed to clean around braces and wires.
Synchronizing your toothbrush
To avoid interference of display messages when
using more than one Oral-B Triumph toothbrush with
SmartGuide in the same household, you need to
assign the handles to their respective SmartGuide.
You can synchronize a maximum of 2 handles with
one SmartGuide. To do so, push the «h/min» button
in the battery compartment for at least 3 seconds.
The SmartGuide shows «L---». Turn on your handle
to start the synchronization process. It is finished
when «L-1-» is displayed. Turn off the handle.
To assign a second handle to the same SmartGuide
turn on the other handle until «L-2-» is displayed.
After having synchronized the second handle, «Full»
will be displayed. Exit the syncronization mode by
pressing the «h/min» or «set» button, otherwise it will
end automatically after 30 seconds.

Cleaning recommendations

After brushing, rinse your brush head under running
water with the handle switched on. Switch off and
remove the brush head. Clean handle and brush
head separately; wipe them dry before reassembling.
Disassemble the charging unit before cleaning. Brush
head compartment and protective cover are dish-
washer-safe. Both basic charger and SmartGuide
should be cleaned with a damp cloth only (picture 5,
page 3).

Wall mount

Use the adhesive tape (k) if you prefer to mount the
SmartGuide on a wall, mirror or other surface. Make
sure the chosen surface is clean and dry. Position
the wall mount (j) with the Oral-B logo readable and
press it evenly and firmly to the wall. Wait 24h before
sliding the SmartGuide into the fixed wall mount
(picture C, page 2). The adhesive tape will not work
on dirt-repellent surfaces.
Subject to change without notice.