72 hours of delivery. Notify the carefully. manual. dealer at the same time. The Trane Company assumes no liability for installations or servicing For installing the unit to operate The unit should be totally inspected performed by unqualified personnel.
Contents General Information System Appearance Location and Preparation of Units Units Installation Connection of Refrigerant Tubing Condensate Drain Piping Electrical Installation Wiring Diagram Dimensional Data Maintenance MS-SVN004-EN L/O- 02091985TRA 21/4/03, 2:44 PM...
System Appearance MCD 512-536 DB/D1 Blower Motor Outlet Collar Evaporator Coil Electric Heater (Option) Condensate Drain Pan Indoor unit Outdoor Unit MS-SVN004-EN L/O- 02091985TRA 21/4/03, 2:44 PM...
Page 5
MCD 048-060 DB/D1 Motor Blower Outlet Collar Evaporator Coil Return Air Plenum Electric Heater (Standard) (Option) Condensate Drain Pan Indoor Unit Outdoor Unit MS-SVN004-EN L/O- 02091985TRA 21/4/03, 2:44 PM...
Location and Preparation of Units Indoor Unit 2. Before cutting, check that no pipes 1. Tools Required for Installation 1. Select a convenient location that or studs are directly behind the (not supplied) allows the air to reach every corner place to be cut.
Connection of Refrigerant Tubing Proper installation prodecure is 2. Remove burrs at the end of the Flare Nut recommended in the Installation copper tube with a tube reamer Manual Package, usually provided (Figure 8). together with the outdoor unit. It is 3.
Condensate Drain Piping Condensate Drain Piping 4. When the drain hose is placed in 1. The drain hose should run straight the room, insulate the hose with down the wall to a level where the foam polyethylene to avoid damage run off will not stain the wall.
Electrical Installation Electrical Installation Indoor Unit All wiring and grounding must comply Remove the right side junction box with local electrical codes. (see previous instructions) to access the terminal base. Wiring Important Safeguards: - Check the unit nameplate for System Wiring Routing electrical rating.
Wiring Diagram CONCEALED FAN COIL UNITS COOLING ONLY MCD 512-536 DB/D1 MCD 048-060 DB/D1 Remove HI-BR wire from TB-1 and replace with EXTRA HI-BLK wire when high speed/cfm is required in the field. EXTRA–HI BLOWER MOTOR LOW MED HI 3 SPEED SWITCH THERMOSTAT POWER SUPPLY 200-240V/1PH/60Hz...
Page 13
Wiring Diagram CONCEALED DX AIR HANDLER COOLING-HEATING MCD 512-524 DB/D1 REMOVE HI-BR WIRE FROM TB-1 AND REPLACE WITH EXTRA HI-BLK WIRE WHEN HI SPEED/CFM IS REQUIRED IN THE FIELD. EXTRA–HI BLOWER MOTOR LOW MED HI HEAT TO HEATING TO COOLING 3 SPEED COOL SWITCH...
Page 14
Wiring Diagram CONCEALED FAN COIL UNITS COOLING-HEATING MCD 530-536 DB/D1 MCD 048-060 DB/D1 Remove HI-BR wire FROM TB-1 and replace with EXTRA HI-BLK wire when high speed/cfm is required in the field. EXTRA-HI BLOWER MOTOR LOW MED HEAT TO HEATING TO COOLING 3 SPEED COOL...
3/4"(19.05) Note: From the experience of our Trane technician, based on the design condition, at velocity at supply air grille of 300 ft/min for bedroom and 400 ft/min for office (based on free face area), the length of the air duct should be more than 3 meters.
Page 16
3/4"(19.05) Note: From the experience of our Trane technician, based on the design condition, at velocity at supply air grille of 300 ft/min for bedroom and 400 ft/min for office (based on free face area), the length of the air duct should be more than 3 meters.
Page 17
3/8"(9.52) Note: From the experience of our Trane technician, based on the design condition, at velocity at supply air grille of 300 ft/min for bedroom and 400 ft/min for office (based on free face area), the length of the air duct should be more than 3 meters.
Maintenance Regular Maintenance Note: Once the air filter is washed, Be sure to disconnect the power dry it completely befor e returning it to before inspection or maintenance of its original position. air conditioner . After cleaning be sure to return it to its original position.
Page 20
35 Mu 8, Poochaosamingprai Road Samrong Tai, Samutprakarn 10130 http://www.trane.com Since The Trane Company has a policy of continuous product and product data improvement, An American Standard Company it reserves the right to change design and specifications without notice. L/O- 02091985TRA...