Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Service & Parts Manual
Advertisement
Table of Contents
Related Manuals for Dimplex MILANOef EDS7001F
Summary of Contents for Dimplex MILANOef EDS7001F
- Page 1 MILANO MODEL EDS7001F PARTS & SERVICE MANUAL...
- Page 2 TABLE OF CONTENTS OPERATION PAGE 3 PARTS DRAWING PAGE 5 WIRING SCHEMATICS PAGE 6 PARTS LIST PAGE 7 LIGHT BULB REPLACEMENT PAGE 8 MAIN POWER ON/OFF SWITCH REPLACEMENT PAGE 9 FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 10 HEATER ON/OFF SWITCH PAGE 12 HEATER THERMOSTAT REPLACEMENT PAGE 13 POWER CORD REPLACEMENT...
-
Page 3: Operation
EDS7001F MILANO NOTE A 15amp, 120 volt circuit is required. A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse blows on a regular basis when the heater is operating. -
Page 4: Resetting The Temperature Cutoff Switch
EDS7001F MILANO RESETTING THE TEMPERATURE CUTOFF SWITCH This unit is equipped with a thermostat that controls the temperature of the room. It does this by turning the heater on and off. The heater is protected with a safety device to prevent overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset. - Page 5 EDS7001F MILANO...
- Page 6 EDS7001F MILANO...
-
Page 7: Replacement Parts
EDS7001F MILANO REPLACEMENT PARTS MILANO DIMPLEX CATALOGUE NO. EDS7001F PART NO. 6900840000 MOD. LEVEL REPLACEMENT PART 1. LOG SET 0438270100RP 2. FRONT DOOR 0438390100RP 3. STOVE TOP 1103740104RP 4. A.C. MOTOR ASSEMBLY 2000140300RP 5. HEATER ASSEMBLY 2000170300RP 6. THERMOSTAT 2300150100RP 7. - Page 8 EDS7001F MILANO If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
-
Page 9: To Replace Main On/Off Switch
EDS7001F MILANO If the stove was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. -
Page 10: To Replace Flame Motor/Flame Rod
EDS7001F MILANO If the stove was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. - Page 11 EDS7001F MILANO If the stove was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
-
Page 12: To Replace Heater On/Off Switch
EDS7001F MILANO If the stove was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. - Page 13 EDS7001F MILANO If the stove was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
- Page 14 EDS7001F MILANO If the stove was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
- Page 15 7001F MILANO If the stove was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
- Page 16 16. Locate and remove all of the heater assembly retaining screws from the bottom panel. 17. Disconnect the wiring clips and connections noting their original locations and remove the heater assembly. 18. Properly orientate the flame motor and connect all of the wiring clips connections in their original locations.