Table of Contents
Advertisement
!
NOTE: A flat head screwdriver can be used to gently
pry between the end of the connector and the switch to
release the wires.
7.
Remove the thermostat control knob by pulling straight
out.
8.
Remove the 2 mounting screws and replace the old
thermostat with the new one.
9.
Reassemble in the reverse order as above.
FLICkER ROD/MOTOR REPLACEMENT
Tools Required: Phillips Head Screwdriver
Flat Head Screwdriver
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for lights, heating elements and top
panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
1.
Open the front control cover.
2.
Remove front glass by removing the 2 outer screws
holding the glass clips. (Figure 3)
3.
Remove the log grate by removing the 4 mounting
screws. (Figure 5)
4.
Remove the log set by lifting straight up.
5.
Slide the light assembly slightly and lift out of the insert
being careful not to damage any of the wiring.
(Figure 8)
6.
Remove the reflector rod from the flicker motor by pull-
ing the end of the rod to the left and separating it from
the rubber sleeve.
7.
Remove the rubber sleeve from the motor shaft.
8.
Disconnect the flicker motor wire from the terminal
block, noting their original locations
Figure 8
8
9.
Remove the 2 motor mounting screws and remove the
flicker motor.
10.
Discard the old flicker motor.
11.
Reassemble in the reverse order as above
HEATER ASSEmBLy REPLACEmEnT
Tools Required: Phillips Head Screwdriver
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for lights, heating elements and top
panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
1.
Remove the 4 retaining screws and lift the top cover off
of the insert being careful not to damage the wiring.
2.
Remove the 4 heater mounting screws from the top of
the top cover to separate the heater assembly.
3.
Remove the 2 heater mounting brackets from the
heater assembly.
4.
Disconnect the 2 heater switch leads from the heater
noting their original locations.
5.
Disconnect the thermal cut-out wire from the wire nut.
6.
Reassemble in the reverse order as above, with the
new component.
REMOTE CONTROL RECEIVER
REPLACEMENT
Tools Required: Phillips Head Screwdriver
Flat Head Screwdriver
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for lights, heating elements and top
panel to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
1.
Remove the 4 retaining screws and lift the top cover
off of the insert being careful not to damage the wiring.
(Figure 9)
2.
Disconnect the wire connections from the circuit board
noting their original locations.
!
NOTE: A flat head screwdriver can be used to gen-
tly pry between the end of the connector and the receiver
board to release the wires.
3.
From inside the insert, break off the six mounting studs
on the circuit board by grasping with pliers and twisting
on the protruding part of the stud, push the remainder
of the studs out through the top panel.
!
NOTE: New mounting studs are supplied with the
replacement circuit board.
4.
Properly orient the new circuit board and reconnect all
of the wiring connections.
POWER CORD REPLACEMENT
Tools Required: Phillips Head Screwdriver
CAUTION: If unit was operating prior to servicing allow
www.dimplex.com
Hide quick links:
Advertisement
Table of Contents
