NOTE: Procedures and techniques that are considered important enough to emphasize. CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment. WARNINg: Procedures and techniques which, if not carefully followed, will expose the user to the risk of fire, serious injury, or death. www.dimplex.com...
OPERATION Remote Control The fireplace is supplied with a radio frequency remote The BLF50 operates in a 3-Stage process. These control. This remote control has a range of approximately stages can be controlled either by the remote control 50 feet (15.25 m), it does not have to be pointed at the...
(Figure 5) mounting brackets The tray has a small lip that goes underneath and • Secure the remaining 4 screws in the media tray. slightly up behind the Partially Reflective Glass - from www.dimplex.com...
Figure 6 " (123 cm) 46" (116 cm) 3" (7.6 cm) 7" (17.8 cm) " (128 cm) 16" 18" (40.6 cm) (45.7 cm) (49.5 cm) " (9.7 cm) Proceed to the instructions within this manual relating power source, taking note of their original configuration. to the repair being performed - see Table of Contents Surface Mount for page number.
(i.e. hardwood flooring), it is recommended that a protective barrier be used underneath, (i.e. cloth, cardboard, thick plastic). Proceed to the instructions within this manual relating Figure 10 Mounting Holes Wall Surface Figure 9 Mounting Holes Mounting Hole www.dimplex.com...
to the repair being performed - see Table of Contents allow a little “give” when feeding the wires around the for page number. covers. Once repair is complete, reassemble in the reverse Lift and remove LED strips out of the light covers and order as above.
10 minutes for lights and heating elements to cool off to avoid accidental burning of skin. off to avoid accidental burning of skin. Tools required: Phillips head screwdriver. Tools required: Phillips head screwdriver Needle nosed pliers. Needle nosed pliers Wire Snips Wire Snips 3/8” ratchet or wrench www.dimplex.com...
Remove the heating assembly cover in the top center CAUTION: Follow “Preparation for Service” instructions by removing the 10 screws on the side brackets: 5 on before proceeding. the left and 5 on the right. Wires from the switch hous- Remove the 4 screws that secure the angled switch ing are connected to this piece, so carefully move it housing cover located just below the Remote Switch-...
WARNINg: Disconnect power before attempting any screws in total are holding the panel: 1 screw on the maintenance or cleaning to reduce the risk of electric left and 1 on the right, inside the unit. There are 3 ad- shock or damage to persons. www.dimplex.com...
Page 13
ditional screws located underneath the front face but do not need to be removed. If the 3 bottom screws to the front panel are accessible in your application, you can remove them to obtain the most clearance for the repair. If they are not acces- sible, you can still proceed with them attached and pulling the front panel forward from the top end by ap- proximately 2”...
ASSEMBLY PART PICTURES 3-STAgE REMOTE CONTROL RECEIVER LED DRIVER BOARD MANUAL CONTROLS - Outside View REMOTE SWITCHBOARD - Inside View www.dimplex.com...
Page 15
LOWER ELECTRICAL HOUSINg With Housing-Cover and Flicker Rod in place LOWER ELECTRICAL HOUSINg With Housing-Cover and Flicker Rod Removed LED LIgHT STRIPS...
Page 16
LED LIgHT STRIP WIRE HARNESS HEATINg ASSEMBLY ELEMENT CONNECTIONS Left and Right Side www.dimplex.com...
Page 17
HIgH TEMPERATURE CUTOUT Below Element Housing BLOWER MOTOR CONNECTIONS Below Element Housing...
Replace Flicker Motor Defective LED Driver Board Replace LED Driver Board Flame not bright or flame not Loose wiring Check wiring connections visible Defective LED Light Strip Replace LED Light Strip Flame Shutter Defective Flicker motor Replace Flicker motor www.dimplex.com...
Page 19
PROBLEM CAUSE SOLUTION Heater Heater is not turning off Improper operation Refer to Operation Section Defective Remote Switchboard Replace Remote Switchboard Defective Remote Control Receiver Replace Remote Control Receiver Heater is not turning on Improper operation Refer to Operation Section Loose wiring Trace wiring in unit.