Table of Contents
Advertisement
Quick Links
EN
IMPORTANT SAFETY INFORMATION: Always read this manual first
before attempting to install or use this fireplace. For your safety, always
comply with all warnings and safety instructions contained in this manual
to prevent personal injury or property damage.
08/53542/0 (AU/NZ) Issue 1
Owner's Manual
Model
BLF5051-AU/
PRISM 50"
1
Advertisement
Table of Contents
Related Manuals for Dimplex BLF5051-AU/PRISM 50"
Summary of Contents for Dimplex BLF5051-AU/PRISM 50"
- Page 1 08/53542/0 (AU/NZ) Issue 1 Owner’s Manual Model BLF5051-AU/ PRISM 50" IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to install or use this fireplace. For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.
- Page 2 Table of Contents Welcome & Congratulations ....3 ImPortAnt SAFety InStruCtIonS ..4 Quick reference Guide ....7 Fireplace Installation .
-
Page 3: Welcome & Congratulations
Welcome & Congratulations thank you and congratulations for choosing to purchase an electric NO NEED TO RETURN fireplace from Dimplex, the world TO THE STORE leader in electric fireplaces. Questions With the Assembly? Please carefully read and save these instructions. -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this appliance. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following: 1. If the appliance is damaged, check with the supplier before installation and operation. - Page 5 IMPORTANT SAFETY INSTRUCTIONS not plug in, regulate and clean the appliance or perform user maintenance. 7. Do not use this appliance in series with a thermal control, a program controller, a timer or any other device that switches on the heat automatically, since a fire risk exists when the appliance is accidentally covered or displaced.
-
Page 6: Save These Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNINg: In order to avoid overheating, do not cover the appliance. Do not place material or garments on the appliance, or obstruct the air circulation around the appliance, for instance by curtains or furniture, as this could cause overheating and a fire risk. -
Page 7: Quick Reference Guide
Quick Reference guide Figure 1 ① the electrical information regarding your electric fireplace can 7" be found on the rating label located on (17.8 cm) the front of the unit, behind the glass. Before installation, please record your fireplace's serial number below for future reference. -
Page 8: Fireplace Installation
Fireplace Installation Site Selection you may wish to locate the fireplace near an existing outlet review and consider all of the (for plug-in convenience). following conditions for installation: • Dimensions of the unit: 128cm NOTE 1: A 10 Amp, 230 Volt x 49.5cm circuit is required. -
Page 9: Surface Installation
Fireplace Installation Figure 2 the fireplace is packaged with a plug Bracket Screws installed for plug-in convenience. Hard wiring the fireplace is also an option by removing the plug from the factory fitted cord and completing the wiring according to national and Local elecrical Codes. - Page 10 Fireplace Installation Figure 3 wall anchors are used and at Wall stud least one is located into a stud. Key-hole 6. remove fireplace from wall Permanent and store in a safe place away mounting hole from traffic. 7. Screw all four (4) supplied #8, 3.8 cm square head mounting screws washers...
- Page 11 Fireplace Installation I n - w a l l R e c e s s e d Figure 4 Installation - 100mm Deep CAUTION: Two people may be required for various steps of this procedure. 1. Prepare a wall with a framed opening of 118.1 cm wide x 42 cm high (Figure 4).
- Page 12 Fireplace Installation - 200mm Deep Figure 6 CAUTION: Two people may Mounting be required for various steps of hole this procedure. 1. Prepare a wall with a framed opening of 124.5 cm wide x 47 cm high (Figure 7). NOTE: The sizing has allowed for 6.4mm around the fireplace insert for ease of installation.
-
Page 13: Front Glass Installation
Fireplace Installation Figure 8 outlet or install an outlet on Mounting hole a nearby wall stud within the wall). • Hard wire the fireplace. NOTE: Hard wiring can be done by removing the plug from the factory fitted cord and completing the wiring according to national and Local elecrical Codes. - Page 14 Fireplace Installation Figure 9 Figure 10 Mounts (4) Front tray Hooks (4) Front glass assembly 3-Position Switch is switched to the off position ("o"). Figure 11 5. If unit is not hard-wired, plug fireplace into a 13 Amp, 230 Volt outlet (refer to note 1).
-
Page 15: Operation
Operation Figure 18 Floating Display WARNINg: this electric firebox turns the unit on and off. must be properly installed before → Activated by pressing the it is used. Standby button on the remote the unit can be controlled by or the unit. either the manual controls which •... - Page 16 Operation to increase the setpoint on • Indicated by the icon and the unit or the remote. the intake temperature being • the on Screen Display will displayed on the on Screen indicate the temperature setpoint Display, for 5 seconds before as it is adjusted.
- Page 17 Operation • Cycles through the different is adjusted. once the timer has preset ambient lighting settings begun, pressing the button of the unit, this includes different will display the time remaining combinations of colours of the before the unit turns off. flame base and media lighting.
-
Page 18: Maintenance
Contact Details Maintenance WARNINg: Disconnect Glen Dimplex Australia Pty Ltd power before attempting any 1340 Ferntree Gully road maintenance or cleaning to reduce the risk of fire, electric Scoresby VIC 3179 shock or damage to persons. Australia Partially Reflective Glass...
Need help?
Do you have a question about the BLF5051-AU/PRISM 50" and is the answer not in the manual?
Questions and answers