Visonic PowerMax+ Easy Start Manual page 4

9)
Trouble Shooting
Q – Display - The system display shows [NOT READY] or [NOT
READY - TROUBLE]
A – There is a fault outstanding, press the status button on any
keyfob or press the
message. Any "...Alarm" messages i.e. "Hall Tamper Alarm" can
be ignored however, zone and tamper open messages need to
be addressed i.e. "Hall Tamper OPEN".
Q – Display - How do I clear the [READY - MEMORY] message?
A – Press the status button on the Keyfob or press
to review the memory condition. Start the ARMING process then
disarm the system. The memory prompt should be cleared.
Q - Tamper - I have fitted a sensor with cover closed but the
system is saying the tamper is OPEN, what is wrong?
A - Typically this can happen on PIR sensors when the back plate is
not fitted well or the PCB board is incorrectly positioned. Remove
the PCB and check that the back tamper clicks when you refit it,
then replace the cover again listening for the tamper to click.
Q – Siren - The internal siren will sound on the control panel but
will not sound the external siren
A - This is due to the abort time found in the Installer mode-
'Define Panel'-menu 5. If this is set to above 0 seconds it will
delay the external siren and telephone communications.
Q – Communication - I have entered the private phone numbers
but the panel does not dial when the system is triggered.
A – You need to also enable option 20 in the define Coms menu.
See section 8 for more details.
Q – Panic – I am pressing the keyfob or panel panic buttons but
nothing happens.
A – You need to enable this facility to operate. In installer mode
press until you see [Define Panel] then press
next until [12: Panic Alarm] then press
to select the type (Silent or Audible) pressing
confirm.
Q – Diagnostics – When I test the devices the diagnostic screen
says certain devices are [NOT OK]
A – Each time you enter the Diagnostic menu the previous
reading are cleared and system needs to see a new signal from
the device. Simply repeat the test but make sure the device is
triggered (tamper or alarm)
11)
User Setting and Operation
you can add/delete keyfobs, set time and date, program phone
numbers etc. To select any of these options enter the user menu by
pressing until [User Settings] is shown, then
PowerMax and Next are registered trademarks of Visonic Ltd. Other names
are the property of their owners. Visonic reserves the right to change information or
specifications without notice. D-302605 (Rev.00)
button repeatedly and listen to each
repeatedly
then press
,
. Within the user settings
Q u i ck Fit K it E a s y St a r t G u id e
then
programming option. Remember if you are changing a setting
you need to press the
3
1
4
2
User operation is via the keypad or keyfob (supplied).
When receiving a phone call from the PowerMax System the
user will hear the House ID message followed by the type of
activation. The call must be acknowledged to prevent the system
contacting other Key-holders. To acknowledge press the "2"
button on the telephone keypad or "6" if you would like to listen
and talk through the PowerMax. Refer to your user guide for
more options.
You can also control the PowerMax remotely by ringing in. To do
this call the PowerMax / House phone number, let it ring twice
then hang up. Wait 20 seconds, then call again. You will hear a
modem type tone, then :-
Press '*', then your user code, followed by '#'
You are now logged in and can use commands like:-
•
*, 1, # to Disarm the system
•
*, 3, # to Arm the system
•
*, 9, # to investigate the system status
•
*, 99,# to log off
. Press
For more options and instructions on how to ring in to the
L
system consult the User guide.
to
NEED HELP?
on 0870 7300830 or email productsupport.uk@visonic.com
End users should contact their place of purchase.
Other products in the Visonic range:-
MCT-220 – Single push button
Ideal for panic or emergency
applications
MCT-550 Flood Sensor
Detects early signs of
flooding within the home
MCT-442 CO Sensor
With inbuilt sounder, a
. Pressing
must for every home
MCT-425 Optical Smoke Detector
LPCP approved
, whilst in the menu will allow you to access the
key twice.
Away
1 1
Home
2 2
Disarm
3 3
Aux
4
4
+ Panic (if enabled)
1 2
Trade customers only call Visonic Product Support
MKP-150
Two way keypad
MCM-140
Single way keypad
MCT-124 – Double push
Handheld panic button
TOwer-20 MCw
Wireless External detector