Table of Contents
Advertisement
10. [FOOT SW] (Foot switch) connector
• Connects to an optional foot switch (Model 8051) for
punch in/out operation.
• Connector type: phone jack
<Caution>
Do not power on the machine with non-specified foot
SW connected to the foot SW jack. When powering on
the machine with non-specified foot SW (latch type foot
SW, etc.) connected to the foot SW jack, there is a case
that the machine does not correctly boot up with "No
Drive!" alter message. In such a case, power off the
machine once, disconnect the foot SW and then power
back on.
INPUT A
BAL
UNBAL
CH ON/OFF
TRACK STATUS
1
13
+6
0
-10
-20
-30
-40
-
13. [TRACK STATUS/TRACK SEL] keys
• While stopped, each key is used to change the track
status among OFF, PLAY and REC (READY).
During playback, pressing the key switches between OFF
and PLAY.
During recording, you cannot change the track status.
• When you view or edit mixer parameters such as pan
and EQ in the "Mix parameter edit" mode (described
later), you can select the target track by pressing the
corresponding [TRACK STATUS/TRACK SEL] key.
• The illumination of each key shows the track status as
follows.
* flashing in red: the track is in REC READY.
* lighting in red: the track is being recorded.
* lighting in green: the track can be played back.
* not lighting (off): the track is muted.
Top panel (Mixer section)
15
14
PHONES
INPUT B
L
BAL
TRACK
EDIT
GUITAR
GUITAR
PGM
PAN
LINE
MIC
LINE
MIC
MIN
MAX
TRIM
UNBAL
TRIM
CH ON/OFF
BOUNCE
PEAK
PEAK
REC EFF
RED
REC
GREEN
PLAY
TRACK STATUS / TRACK SEL
2
3
4
5
6
+6
+6
+6
+6
+6
0
0
0
0
0
-10
-10
-10
-10
-10
-20
-20
-20
-20
-20
-30
-30
-30
-30
-30
-40
-40
-40
-40
-40
-
-
-
-
-
24
11. [PEAK] indicators
• Each indicator lights up when the corresponding input
signal reaches the clipping level.
• Set the [TRIM] knob properly not to light the indicator.
12. [CH ON/OFF] keys
• Each key is used to turn on and off of the
corresponding channel. When on, the key illuminates.
See the following description for details about how to use
each element.
18
16
20
17
19
21
ST OUT
FOOT SW
R
MIX PARAMETER
SCENE
SCENE SEQ.
DIGITAL MULTITRACKER
FADER
MAP
EQ
EFFECT
ON/OFF
2TRK MODE
MASTERING
TRAINING
F1
OFF
MUTE
STATUS
/SEL
7/8 2TRK
MASTER
CURSOR
+6
+6
0
0
TIMEBASE
SETUP
SEL
-10
-10
F1
F2
AUTO
PUNCH
LOOP
-20
-20
-30
-30
EDIT
EDIT
-40
-40
RECORD
STOP
-
-
23
14. [BOUNCE] key
• Turns the bounce mode on or off.
When on (the key lights), tracks 7-8 are automatically
armed for recording, allowing track 1 through 5 signals
to bounce to track 7 and 8.
• Pressing this key while holding down the [SHIFT] key
enters the "REC EFFECT" mode, in which rerecording a
recorded track with applying the "insert effect" is
possible. While the "REC EFFECT" mode is active, the
[BOUNCE] key flashes in red. To exit the "REC EFFECT"
mode, press the [BOUNCE] key again.
15. [MIX PARAMETER-PAN] key
• When viewing or editing the pan pot setting, press this
key.
• Select the track to be viewed or edited by pressing the
corresponding [TRACK STATUS/TRACK SEL] key.
15
Names and functions
ACCESS
PHANTOM
F2
F3
JOG
SHUTTLE
EXIT
/NO
EJECT
ENTER
/YES
UNDO
/REDO
F3
SHIFT
LOCATE
WAVE FORM
VARI
PITCH
SCRUB
EDIT
MARK
DELETE
PLAY
REWIND
F FWD
LOCATE ABS 0
LOCATE REC END
22
Advertisement
Table of Contents
