Operating instructions for condenser tumble dryer T 4452 C To avoid the risk of accidents or damage to the machine it is to read these operating instructions before it is installed or used for the first time. M.-Nr. 06 067 770...
^ Make sure that your laundry is thoroughly spun before drying. The transport and protective packing has been selected from materials which The higher the spin, the greater the are environmentally friendly for disposal savings that can be made in energy and can normally be recycled.
......... . 2 Disposal of the packing material .
..........23 Emptying the condensed water container .
..........42 Electrical connection U.K.
This machine is not a toy! To avoid liability. Repairs should only be the risk of injury, do not allow undertaken by a Miele approved children to play on or near it, or to technician. play with the controls. Supervise its Ensure current is not supplied to the use by the elderly or infirm.
If the connection cable is faulty it condensed water is allowed to freeze in must only be replaced by a Miele the pump, hoses and / or condensed approved service technician to protect water container. the user from danger. If the water is drained externally...
Always close the door after use. This way you will avoid the danger Accessory parts may only be fitted when expressly approved by Miele. – children climbing onto or into the If other parts are used, guarantee, dryer or hiding things in it.
g Start/Stop with indicator lights. For starting the programme selected For selecting a drying programme. and cancelling a programme once it has started. The indicator light flashes while a with indicator lights. programme is being selected and Various Extras (options) can be then is on constantly when the added to the drying programmes.
The relevant indicator light comes on each time a button is pressed. The display shows: – the programme duration (time remaining); The indicator or check light marked PC is explained in "After Sales Service". – the delay start time; – check messages; –...
be partially dried using the Woollens hand care programme. Before drying check the drying – Down-filled garments have linings symbol on the wash care label. If which may shrink, depending on the there are no symbols dry at your own quality of the item.
The headings numbered (A, B, C ...) ^ Press the door button to open the show the operating sequence and can door. be used as a brief guide to using your ^ Load the laundry loosely into the machine. drum. Do not overload the drum.
Switching on / off ^ Press the e or - buttons repeatedly until the indicator light for the ^ Each press of the top button selects programme you want lights up. or deselects either the Short or Low – Extras and drying level indicator temperature Extra.
You can a select a drying level for the A buzzer sounds (at intervals for a Cottons, Minimum iron and Automatic maximum of 1 hr) to let you know the programmes. programme has finished. You cannot select a drying level for the ^ Press the Buzzer button.
^ Press the Start/Stop button. The indicator light Anti-crease / Finish comes on. The indicator light for the – The indicator light for the Start/Stop drying stage reached (depending on button will then change from flashing the programme selected) will also to being on constantly.
Not all the Extras are suitable for selecting with every programme. Helps prevent creasing, if laundry is not normally removed immediately after the end of a programme. – The drum will turn at intervals for up to an hour. ^ After you have selected a programme, you can press the appropriate Extra button to select or deselect it.
^ Press the Start/Stop button. The start of a programme can be delayed by up to 24 hours (24^). The Delay start time will be interrupted. ^ Press the Delay start button After selecting a programme: repeatedly until the time you require ^ Press the Delay start button appears in the display in h mins.
Max. load: 5 kg* Fabric type Multi-layered fabrics, which would not be thoroughly dried using the Normal+ programme. Do not dry jersey fabrics in the Extra dry programme as they have Notes a tendency to shrink. Extras Short or Low temperature, Anti-crease Max.
Max. load: 2.5 kg* Fabric Minimum iron items made of synthetic or blended fabrics which are not dried adequately in the Normal programme (e.g. pullovers, type dresses, trousers). Notes Spin minimum iron fabrics for at least 30 seconds in the washing machine before drying.
Max. load: 2.5 kg* Fabric type – Cottons and linen fabrics. – Minimum iron items made of mixed fibres, e.g. cottons / synthetics, such as cotton trousers, jackets, shirts. Notes – Smooths out creasing caused during the spin cycle in the washing machine.
^ Press the Door button. You cannot change to another programme once a programme has ^ Open the door. started (this prevents unintentional alterations). However, you can still Do not touch the back of the select or deselect the buzzer and drum when adding or removing anti-crease.
The system lock prevents your Before you begin, first ensure that: machine being used without your knowledge. – The tumble dryer is switched off. – The door is closed. It can be activated if wished. A Press the Anti-crease and DRYING The dryer's electronics are locked.
The condensed water will be collected in the condensed water container unless the appliance has been fitted with a drain hose (see installation). The condensed water container should be emptied after every drying programme or as soon as the Empty out container indicator light comes on.
The fluff which is created by the drying is available as an optional extra from process is collected by the fluff filters in your Miele dealer or the Miele Spare the door and the door opening. Clean Parts Department. the filters after drying programme.
^ Dry all parts with a soft cloth. ^ Rinse the filters under hot, running ^ A microfibre E-Cloth is available from water. the Miele UK Spare Parts Department which is suitable for cleaning ^ Then shake the filters until no more surfaces such as stainless steel, water droplets are visible.
Detergent residue, hair and fine fluff from the dryer can get through the fluff filters and block the condenser unit. Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage. the condenser unit at least twice a year.
If you cannot see any fluff: ^ Replace the condenser unit (see following page). If you can see some fluff: ^ Clean the condenser unit as described below. ^ When rinsing the condenser unit, make sure you position it as shown in the next two illustrations.
^ With the handle facing upwards, push the condenser unit back into position in its housing. ^ Turn the lever down to the horizontal position, making sure that the hook on the lever clicks into the groove. When replacing the inner cover after cleaning, ensure that the rubber seal fits correctly into the groove.
With the help of the following notes minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting the Service Department. Repair work to electrical equipment should only be carried out by a suitably qualified person in accordance with local and national safety regulations.
Fluff is principally the result Fluff is collected by the fluff of friction when garments filters and can be easily are being worn and removed (see "Cleaning washed. Machine drying and Care"). hardly causes any fluff to form and has been established by research institutes to have no effect on the lifetime of fabric.
: Before attempting to remedy one of the following causes, switch the dryer off and switch on again to start the programme again. Ventilation to and from the Open a door or window dryer may be insufficient while the machine is in (e.g because it is installed in operation for increased air a small room).
The inner cover of the – Ensure that the condenser unit has not condenser unit is been locked properly positioned correctly and/or the condenser unit lock the cover. has not been positioned – Check the rubber seals. correctly. Fluff has collected at the –...
– Then start the programme again. If the programme stops again and the fault message reappears there is a fault. Contact the Miele Service Department. Empty out The condensed water – Empty out the condensed container container is full or there water container.
Hand iron If the programme stops Machine iron again and the fault message reappears there is a fault. Contact the Miele Service Department. The electronics are in the This is not a fault. process of calculating the drying time and require a few seconds longer.
^ Turn your wrist to make the cover open downwards. The temperature resistant lamp should only be ordered from your Miele dealer or the Miele Spare Parts Department. The lamp must not exceed the maximum wattage quoted on the data plate and on the lamp cover.
Service Department, please quote the Optional accessories for these dryers model and serial number of your are available from your Miele Dealer or machine, both of which are shown on from the Miele Spare Parts Department. the data plate situated on the right hand side below the drum aperture.
a Supply cable for electrical e Service panel for condenser unit connection f Four height-adjustable screw feet b Condensed water container g External drainage options (e.g. via c Control panel wash basin, wash basin drain outlet, or gully). d Door...
* Available as an optional accessory from your Miele dealer or the Miele Spare Parts Department. The dryer should not be installed The building under kit is supplied with next to a refrigerator or freezer.
(WTV) to match your washing machine is required. * Available as an optional accessory from your Miele dealer or the Miele Spare Parts Department. Stacking kits must be fitted by a suitably qualified fitter. After each use a small quantity of...
Important: do not let the drain the Miele Spare Parts Dept. hose become kinked as this could damage it. From the back of the dryer at the top:...
If this nut has a flat disc sealing it you should take the disc out first. The drain hose can be connected Important: if this nut has a washer or directly to a sink drain outlet. seal in it this must not be removed! ^ Attach the end of the hose to adapter ^ Use a screwdriver to tighten hose clip...
All electrical work should be carried out only by a suitably qualified and If this machine is fitted with a competent person, in strict accordance non-rewireable plug and the socket with national and local safety outlets are not suitable for the plug regulations.
If the colours of the wires in the mains lead of this machine do not correspond with the coloured markings identifying the terminals of your plug, proceed as follows: ^ The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol z or coloured green, or...
EN 61121 test programme : 800 rpm (70 % residual moisture) 3.40 kWh 89 mins Max. load 5 kg 800 rpm (70 % residual moisture) 2.70 kWh 74 mins Max. load 5 kg 1000 rpm (50 % residual moisture) 1.25 kWh 38 mins Max.
Height 85 cm (adjustable +0.7/- 0.7 cm) Height without lid 82 cm Width 59.5 cm Depth 58 cm Depth with door open 106 cm Weight 54 kg Drum volume 100 litres Maximum capacity 5 kg dry weight Capacity of condensed water container approx.
Programmable functions for changing standard settings...
A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. If you want the laundry to be drier you can reduce the residual moisture B Press the I-On/0-Off button in. level for the Cottons programmes. C Wait until the Start/Stop indicator light –...
A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. If you want the laundry to be drier you can reduce the residual moisture B Press the I-On/0-Off button in. level for the Minimum iron C Wait until the Start/Stop indicator light programmes.
A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. The electronics will memorise the drying level and any Extras selected B Press the I-On/0-Off button in. for the current drying programme. C Wait until the Start/Stop indicator light The Memory function comes on .
A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. The Cooling down phase which takes B Press the I-On/0-Off button in. place at the end of a programme can C Wait until the Start/Stop indicator light be lengthend if required.
A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. The Clean out airways indicator light can be deactivated. B Press the I-On/0-Off button in. The Clean out airways indicator light C Wait until the Start/Stop indicator light comes on .
A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. An audible tone sounds each time a button is pressed. B Press the I-On/0-Off button in. The machine is delivered with the C Wait until the Start/Stop indicator light keypad tone switched off.
Alteration rights reserved/0504 M.-Nr. 06 067 770 / 00 This paper consists of cellulose which has been bleached without the use of chlorine.