Advertisement
The YTA50 is a head mount type of temperature transmitter that
accepts thermocouple or RTD input and converts it to a 4 to 20
mA DC signal for transmission. The YTA50 conforms to the
standard DIN form B head mounting.
It is imperative that usres observe the instructions in this
manual to ensure the protection and safety of operators.
1.
MODEL AND SUFFIX CODES
Model Suffix code
YTA50 ..................
Temperature Transmitter (Head Mount Type)
-A .............
Output
4 to 20 mA DC
Signal
Optional
/KS2
CENELEC ATEX intrinsically
Specifications
safe approval
CENELEC ATEX/FM intrinsically
/DS2
safe approval combination
2.
WARRANTY
The warranty period of the instrument is as of condition shown
when purchasing. Any trouble arising during the warranty period
shall be replaced at free of charge.
The following problems or troubles shall not be eligible of
charge-exempt repair.
• Caused by improper usage or storage of the customer which
exceeds the specification requirements.
• Caused by mishandling or modification.
• Caused by fire, earthquake or other acts of God that are not
directly a result of problems of the instrument.
4.
STANDARD SPECIFICATIONS
Accuracy
See table in the right.
Cold Junction Compensation Accuracy(For T/C only)
±1°C(±1.8°F)
Ambient Temperature Effects (per 10
See table in the right
Input
Type
Standard
ranges °C
T/C
B
IEC584
400 to 1820
E
-100 to 1000
J
-100 to 1200
K
-180 to 1372
N
-180 to 1300
R
-50 to 1760
S
-50 to 1760
T
-200 to 400
L
DIN43710
-100 to 900
U
-200 to 600
W3
ASTM E988-90
0 to 2300
W5
0 to 2300
Pt100
IEC751
RTD
-200 to 850
Ni100
-60 to 250
DIN43760
DC Voltage [mV]
-10 to 800 mV
Resistance [ ]
0 to 5000
*1 : The value whichever is greater. value in % indicates the
% of span.
Power Supply Effects
±0.005% of FS per Volt
RFI Effects
Tested per EN 61326, field intensity up to 10 V/m.
EMC Conformity
EN 61326
Maximum Zero Offset
±50% of the maximum temperature
Descriptions
EEx ia llC T1-6
Amb. Temperature
T1-4: -40 to 85°C
T5-6: -40 to 60°C
CENELEC:
EEx ia llC T1-6
FM: IS Class I, Div.1,
Groups A, B, C & D
°
C Change)
Temperature
Minimum
1
Accuracy *
span °C
effect *
200
±0.1% or ±2.0°C
±0.1% or ±2.0°C
50
50
±0.1% or ±1.0°C
±0.1% or ±0.5°C
50
100
200
±0.1% or ±2.0°C
±0.1% or ±2.0°C
200
50
±0.1% or ±1.0°C
±0.1% or ±0.5°C
50
75
200
±0.1% or ±2.0°C
±0.1% or ±2.0°C
200
25
±0.1% or ±0.2°C
±0.1% or ±0.1°C
25
±0.1% or ±0.01mV
±0.1% or ±10 V
5 mV
30
±0.1% or ±0.1
±0.1% or ±0.1
T02E.EPS
3.
HANDLING PRECAUTIONS
(1) Read this manual thorughly and carefully before handling
the instruments. Observe the instructions.
(2) Store the product in location that meets the following
requirements.
• No exposure to rain or water
• No major mechanical vibration or shock
• Humidity and Temperature limitations
• Ordinary conditions(25°C, 65%) is preferable.
Otherwise, as of specified in "Standard Specifications."
(3) Avoid corrosive atmosphere for storage and installation.
(4) For safe installation of the transmitter in hazardous area,
the following must be observed. The module must only be
installed by qualified personnels who are familiar with the
national and international laws, directives, and standards
that apply to this area.
(5) Yokogawa will not be liable for malfunctions or damage
resulting from any modification made to this instrument by
the customer.
T01E.EPS
Input Signal Source Resistance (for T/C input)
10 MΩ, or 3 kΩ at power-off
Input Lead Wire Resistance (for RTD input)
5 Ω per wire or lower
Burnout
High (21.6 mA or more) or Low (3.6 mA or less)
Output
Two wire 4 to 20 mA DC
1
Response Time
1 to 60 sec (as specified upon shipment)
Ambient Temperature Limits (Option code may affect limit.)
–40 to 85°C (–40 to 185°F)
Ambient Humidity Limits
5 to 90% RH at 40°C (104°F)
Supply Voltage
7 to 35 V DC
7 to 30 V DC for Intrinsically safe type
Load Resistance (Limitation)
0 to (E–7)/0.023 [Ω], where E is power supply voltage.
Ex. 739 Ω max. @ 24 V DC
Isolation
Input/output isolated to 1500 V AC.
Mounting
DIN form B head mounting
Terminals
M3 screws
Weight
50 g(0.11 lb)
Advertisement
