Advertisement
Now start...
with dryer in laundry area.
1
1 Take tape off front corners of dry
2
n
Open dryer and remove
the literature
and parts packages.
(If dryer has a drying
rack it should be removed
also.)
Remove
all
parts from the plastic packages.
Line these
up next to your tools so each
part is there
when you need it. Check
to see that you
have these parts:
Numbers
correspond
to steps.
4 legs
13
n
To
exhaust
the dryer.
see Exhaust
requirements.
Connect
exhaust
duct to exhaust
hood.
Use duct
tape
to seal all
joints in exhaust
duct.
Use caulking
compound
to seal exterior
wall opening
around
exhaust
hood.
3
n
Remove
the tape that holds the
drum to the cabinet.
(Some dryer drums
are not taped
for shipping.)
Move the
drum by hand to make certain
all tape
has been removed.
Wipe the interior of
the drum thoroughly
with a damp
cloth
before
using the dryer.
8
n
Move the dryer close to its final
location.
To make sure the dryer is level,
take a carpenter's
level and place
it on the
top of the dryer, first side to side, then front
to back.
If the dryer is not level, screw the
legs of the dryer up or down to adjust.
14
n
Plug
the power
supply
cord into the
grounded
outlet.
A
L)
n
Take two of the cardboard
corners
from the carton
and place
them on the floe
in back of the dryer.
9
H Remove
the red cap from the gas
15
n
Turn the
1
dryer on to remove
air from the gas
supply line. Using a
R
full heat cycle
(not
4
the air cycle).
let the
pipe.
Move the dryer into its final position.
5
n
Firmly grasp the body of the dryer
and gently
lay it on its back on the
cardboard
corners.
10
n
Connect
gas supply to dryer.
Use pipe-joint
compound
resistant to the
action
of L.P. gas for gas connections.
If
flexible
metal tubing
is used, be certain
there are no kinks.
dryer run for at least
:
five minutes.
If the
timer control
knob
6
n
With one of the
burner does not ignite and you can feel no
heat inside the dryer, shut off the dryer for
five minutes,
Check
that the gas supply line
shutoff valve is in "ON" position.
Repeat
the
five-minute
test.
legs in hand, check
the
ridges for a diamond
marking.
That's how far
the leg is supposed
to go
into the hole.
Start to
screw the legs into the
holes by hand.
A little
liquid detergent
to lubricate
the legs will
help.
supply line
11
n
Open the shutoff valve in the
gas supply line.
16
n
Check
to see that all of the parts
you removed
from the installation
parts.
packages
in Step 2, Panel C are now
installed
in the dryer.
If you still have an extra
part, go back through
the steps to see what
you skipped.
17
n
Check
to make sure you have
all the tools you started
with in Step A,
Panel A.
Use a 1 ti wrench
or socket to finish turning
the legs until you reach
the diamond
mark.
7
n
Now stand the dryer up.
12
n
Use a brush and liquid detergent
To
get
the most efficient use
from your new dryer, read
your Use and Care Guide.
Keep Installation Instructions
and Guide close to dryer for
easy reference.
to test all external
gas connections
for leaks.
Bubbles around
connections
will indicate
a
leak.
If a leak appears,
shut off gas valve
controls
and adjust connections,
Then
check
connections
again.
Panel C
Advertisement
