Download Print this page

Advertisement

Commercial
Dryer
Installation
Instructions
MPORTANT:
?ead and save
lhese instructions.
Important:
Read
these instructions
before
you start to install
the dryer.
Save Installation
Instructions
for local electrical
inspector's
use.
Keep
Installation
Instructions
for future
reference.
J
Part No. 3395316 Rev. C

Advertisement

   Summary of Contents for Maytag 3395316

  • Page 1

    Commercial Dryer Installation Instructions MPORTANT: ?ead and save lhese instructions. Important: Read these instructions before you start to install the dryer. Save Installation Instructions for local electrical inspector’s use. Keep Installation Instructions for future reference. Part No. 3395316 Rev. C...

  • Page 2

    Important: Observe all governing Before you start... codes and ordinances. Protectlon from weather: Proper Check locatlon where dryer will be Failure to meet codes and operation requires temperatures used. Proper installation is your ordinances could lead to fire above 45°F (7.2%). responsibility.

  • Page 3

    Tools and matetials needed for installation: adjustable wrench level utility knife pliers Phillips screwdriver duct tape The supply line shall be flat-blade screwdriver I” socket wrench equipped with a shutoff valve. Thls valve should be located in the same Gas supply room as the dryer and should be in a requirements location...

  • Page 4

    zcordmended grounding Electrical reauirements For your personal safety, these dryers must be grounded. Each dryer is equipped with a power supply cord having a 3-prong grounding plug. To minimize shock hazard, the cords must be plugged into mating 3-prong Electrlcal Shock IHazard grounding-type wall receptacles, Electrlcal ground Is required on...

  • Page 5

    Thls chart applies only to lndlvldually Exhaust materials are not Exhaust exhausted unlts. supplied. requirements EXHAUST HOOD TYPE better exhaust fi%rt aitilow airflow Fire/Health Hazard t2.s 5igi Do Not use non-metal, flexible duct. MAXIMUM LENGTH OF I-INCH DIAMETER RIGID METAL DUCT Do Not use metal duct smaller 41 Fr 36 Fr.

  • Page 6

    Exhaust duct If dryer Is Installed In a confined area such as a bedroom, bathroom connection closet, it must be exhausted to the Product Damage outside and provision must be made for enough air for combustion Keep alr openlngs free of dry- ventilation.

  • Page 7

    of the cabinet. If duct extends too far To connect exhaust duct to make the exhaust duct ;rFeugh the right or left connection, mark a line around straight duct one inch out from the cabinet. Remove the duct and elbow and cut the straight pipe to the length...

  • Page 8

    Wablnet screw head rear (fastens yg;&y-b Floor Damab Wear gloves to protect hands from Slide dryers onto cardboard sharp edges that may be present. hardboard before mating across floor. Failure to do so may result In Failure to do so may cuuse personal Injury.

  • Page 9

    Recessed area Front view and closet installations AddItIonal clearances maybe required for wall, door and floor Fire/Health Hazard mokiln extema Exhaust dryers to the outslde to Closet exhousf prevent exposure to substances In elbow door Used. the gas fuels and combustion byproducts which may be harmful to your health.

  • Page 10

    Now start... Numbers With dryer in laundry area. correspond to steps. Personal InJury Hazard More than one person Is required to lift. tilt. or move stacked dryers because of weight and size. Failure to follow these lnstructlons may result In personal InJury. Take two of the cardboard corners from the carton and place...

  • Page 11

    The installation is now complete. Personal Injury fiazard Floor Damage To prevent tlpplng, tetlher bracket Slide dryers onto cardboard must be secured to wall studs or hardboard betore movlng across concrete wall. floor. Failure to do so could result In Failure to do so may result In personal Injury.

  • Page 12

    Burner information may be found on the rating plate in the door well of the dryer. Printed on recycled paper. 10% post consumer waste/ 50% recovered matertals. Part No. 3395316 Rev. C Printed in U.S.A. 01994...

Comments to this Manuals

Symbols: 0
Latest comments: