Download Print this page
KitchenAid 3397629 Installation Instructions Manual
KitchenAid 3397629 Installation Instructions Manual

KitchenAid 3397629 Installation Instructions Manual

Advertisement

Quick Links

Have questions about your dryer?
Check your Use and Care Guide for a toll-free number to call, or call your
dealer. The dealer is listed in the Yellow Pages of your phone directory
under "Appliances
-
Household -
Major -
Service and Repair."
When you call, you will need the dryer model number and serial number.
Both numbers are on the model/serial
rating plate located in the door well
behind the dryer door and on front of opening.
Record
the numbers
here for handy
reference:
Model
No.
Serial
No.
Moving dryer to a new location?
Check with a licensed electrician to confirm that supply voltage at new home matches
voltage specified on the model/serial
rating plate.
Shut off electrical
supply to dryer.
Unplug
power
supply
cord and tape it
\
(Or disconnect
power
\&
securely to dryer.
SUDPIV cable from
Tape top
to cabinet
Slide dryer onto'cardboard
or hardboard
before
moving
it across the floor to
prevent
damaging
floor covering.
Electric Dryer
Part No. 3397629
IMPORTANT:
Read and save these instructions.
IrEtaller:
Leave Installation
Instructions with homeowner.
Homeowner:
Keep Installation
Instructions for future reference.
For best performance,
install dryer according to
Installation
Instructions.
Failure to complete
installation
as instructed could void warranty.
Save
Installation
Instructions for local electrical inspector's use.

Advertisement

loading

Summary of Contents for KitchenAid 3397629

  • Page 1 Tape top (Or disconnect power \& to cabinet SUDPIV cable from Electric Dryer Part No. 3397629 IMPORTANT: Read and save these instructions. IrEtaller: Leave Installation Instructions with homeowner. Homeowner: Keep Installation Instructions for future reference.
  • Page 2: Exhaust Hood

    (with ground wire). All current-carrying wires must be insulated. See Panels D and E. 1 O-GAUGE SOLID COPPER WIRE. (Do not use aluminum.) at least 4 feet long. Part No. 3397629 Printed in U.S.A. 0 1997 Benton Harbor, Michigan 49022...
  • Page 3: Recessed Area/Closet Installation

    Dimensions with feet extended shown 1” from bottom of dryer. back exhaust al block cover Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Place dryer at least 18 inches above the floor for a garage installation. Failure to do so can result in death, explosion, or fire.
  • Page 4: Determine Vent Length

    Dura Safe’” venting products are recommended Mobile home installation requirements and are available from your dealer. If codes permit, this appliance is suitable for mobile Four-inch diameter vent must be used. home installations. The installation of the dryer must Use a heavy metal vent. Do Not use plastic or metal conform to Manufactured Home Construction foil vent.
  • Page 5: Power Supply Cord

    See installation steps for details. Check operation. Turneon Chec&hat power supply. dryer is level. Disctnnect power suPPlY. Make-electrical connection. Put on safety glasses and gloves. w Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood. Connect vent to exhaust hood with 4”...
  • Page 6 4. Remove center terminal block screw. 5. Remove appliance ground wire (green with yellow stripes) from external ground connector screw v. Fasten under center, 6. Connect ground wire ._-:-^I LI--1. ___^... silver-colored terrrlrrldl UWCR ww (green) of power supply cord to external ground conducto’...
  • Page 7 Where local codes permit connecting cabinet-ground conductor to neutral wire: Loosen or remove center terminal Preparing the wire: block screw. three-wire with ground wire: Bare 5. Place the hooked end of the wire cut short. neutral wire (white or center) of wire is not used.