Advertisement
Your safetv and the safetv
of others
is' very importank
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all safety
messages.
q !
This is the safety alert symbol. This
symbol alerts you to hazards that can
kill or hurt you and others. All safety
messages will be preceded by the safety alert
symbol and the word "DANGER" or
"WARNING". These words mean:
36" (91.4 c'm)
cooktop
height with
leveling
legs
lowered
l-1/2 turns
12-l 12"
(57.1 cm)
Al
You &l
be killed or seriously
injured
if
you don't follow
instructions.
You can be killed or seriously
injured
if
you don't follow
instructions.
All safety messages will identify the hazard,
tell you how to reduce the chance of injury,
and tell you what can happen if the
instructions
are not followed.
(2.5 cm)
4
Important:
Observe all governing
codes and
ordinances.
Failure to meet codes and
ordinances
could lead to fire or electrical
shock.
Proper installation
is your responsibility.
A
qualified technician
must install this range. Make
sure you have everything
necessary for correct
installation.
It is the installer's
responsibility
to
comply with installation
clearances specified on
the model/serial
rating plate. The model/serial
rating plate is located on the oven frame behind
the storage drawer panel.
Check location where range will be installed.
The range should be located for convenient
use
in kitchen.
When installing
a range under existing cabinets
and the installation
does not meet the minimum
cabinet clearances, install a range hood above
the cooktop to avoid burn hazards.
ALL OPENINGS IN THE WALL OR FLOOR
WHERE RANGE IS TO BE INSTALLED MUST
BE SEALED.
Cabinet opening dimensions
that are shown
must be used. Given dimensions
are minimum
clearances.
Grounded electrical
supply is required. See
"Electrical
requirements,"
Panel B.
It is the customer's
responsibility:
To contact a qualified
electrical installer.
To assure that the electrical installation
is
adequate and in conformance
with National
Electrical Code, ANSVNFPA 70 - latest edition*
and all local codes and ordinances.
Mobile home installation
The installation
of this range must conform with
the Manufactured
Home Construction
and
Safety Standard, Title 24 CFR, Part 3280
[formerly
the Federal Standard for Mobile Home
Construction
and Safety, Title 24, HUD (Part
28011 or, when such standard is not applicable,
the Standard for Manufactured
Home
Installations,
ANSI A225.1/NFPA 501A*, or with
local codes.
When this range is installed
in a mobile home, it
must be secured to the floor during transit. Any
method of securing the range is adequate as
long as it conforms to the standards listed
above.
Four-wire power supply cdrd or cable must be
used in a mobile home installation.
The
appliance wiring will need to be revised. See
"Four-wire
electrical connection,"
Panel B.
Copies of the standards
listed may be obtained
from:
* National
Fire Protection
Association
Batterymarch
Park
Quincy, Massachusetts
02269
--"
(76.2 cm) min.
25" (63.5 cm) countertop
depth
24" (61 cm) base cabinet
depth
36" (91.4 cm) countertop
height
When installed
in a 24" (61 cml base
cabinet
with 25" (63.5 cm)
countertop
-
front of oven door
protrudes
l-7/8"
(4.8 cm) beyond
24" (61 cm) base cabinet.
Note: 24" (61 cm) min. when bottom
of wood
or metal cabinet
is
protected
by not less than 114"
(0.64 cm) flame retardant
millboard
covered
with
not less than No. 28
MSG sheet steel, 0.015" (0.4 mm)
stainless
steel, 0.024" (0.6 mm)
aluminum
or 0.020" (0.5 mm)
copper.
30" (76.2 cm) min. clearance
between
the top of the cooking
platform
and the bottom
of an
unprotected
wood
or metal cabinet.
30-3/8"
(77.2 cm)
I
l *
min. clearance
from both sides
of range to side
wall or other
combustible
material
between
upper
cabinet
and
8" (20.3 cm) to
22" (55.9 cm) from
either cabinet,
7" (17.8 cm) max.
Do not
seal range
to side
cabinets.
between
cutout
The floor-mounted
anti-tip
bracket
MUST be installed.
To install
the
anti-tip
bracket
shipped
with the
range, see Panel C and the anti-tip
bracket
template/instruction
sheet.
The cook-top sides of the slide-in range fit over
the cutout edge of your countertop.
If you have a square finish (flat) countertop
and
the opening width is 30-3/B" (77.2 cm), no
countertop
preparation
is required.
Formed front-edged
countertops:
Must have
molded edge shaved flat l/4" (0.64 cm) from
each front corner of opening.
Tile countertops
may need trim cut back
l/4" (0.64 cm) from each front corner and/or
rounded edge flattened.
If countertop
opening width
is greater than
30-3/8" (77.2 cm), adjust the l/4" (0.64 cm)
dimension.
Countertop
must be level. Place level on
countertop,
first side to side; then front to back.
If countertop
is not level, range will not be level.
Oven must be level for satisfactory
baking
conditions.
/ -..
/ ' s 4
114'
(0.64 cml
Cooktop
sides of range fit over
edges of countertop
opening.
wood floors:
l/8"
drill bit
concrete/ceramic
floors:
3/16" carbide-tipped
masonry
drill bit (Hammer
may be needed for
anchors.)
2 plastic
anchors
2 screws
(#IO x l-1/2")
floor-mounted
Not shown:
anti-tip
bracket
literature
pack
Brackets
must be securely
mounted
to sub-floor.
Thickness
of flooring
may require
longer
screws to
anchor bracket
to sub-floor.
Longer screws
are
available
from your local hardware
store.
tape or ruler
Panel A
/ 6F
%
safety
-'v :,
h'
a
:
z
. .
,I
glasses
gloves
channel
lock
Advertisement
