Function Setting List - JUKI IP-110 Instruction Manual

(2) Function setting list

For the detals of the functon, refer to the Instructon Manual and Engneer's Manual for SC-50.
No.
 Soft-start functon
5 Flcker reducton functon
6 Bobbn thread countng functon
7 Bobbn thread countng down unt
*  Number of revolutons of reverse sttchng
Desgnaton of needle bar poston at the tme of
0
sewng machne stop
Clck sound of key swtch functon

(Key mounted on SC-50 man unt and IP-0E panel)
3 Bobbn thread counter start prohbtng functon
4 No. of pcs. counter
5 Reverse sttchng swtch functon
 Alternate vertcal movement amount nput functon
9 Reversng brake start angle
Alternate vertcal movement amount output delay
20
tme
Presser lftng functon when pedal s n neutral
2
poston
Panel compensaton SW functon changeover
22
functon
24 Presser nput functon for standng sewng machne
25 Thread trmmng acton condtons
26 Reverse sttchng output prohbtng secton 1
27 Reverse sttchng output prohbtng secton 2
2 Reverse sttchng one-shot revoluton delay tme
29 Back solenod ntal start sucton tme
30 Reverse feed sttchng on the way functon
Number of sttches of reverse feed sttchng on the
3
way
Effectve condtons of reverse feed sttchng on the
32
way durng stop
Thread trmmng functon by reverse feed sttchng on
33
the way
* 35 Number of revolutons of low speed
36 Number of revolutons of thread trmmng
Number of revolutons of soft-start
37
(Max. depends on sewng machne used.)
Standard set value may, however, change from the aforementioned one depending on the sewing machine used. In addition, function and set
value are subject to be changed without permission to improve function and performance.
Do not change the set value of the functions with * mark since the functions are for maintenance. If the standard set value set at the time of
delivery should be changed, it is very dangerous since breakage or deterioration of the sewing machine will be caused. When it is necessary
to change the standard set value, please purchase the Engineer's Manual and follow the instructions.
Function
– 43 –
Panel display
Setting level
Standard set value
N-SOFT
2
T-ACC
2
SCBOB
2
RATIO
2
2
2
SOUND
2
ASCNT
2
2
F-BTSW
2
F-INDL
2
A-SARR
2
T-DVMS
2
N-NPL
2
F-CMSP
2
F-FLSW
2
F-TRMC
2
A-BTINH
2
A-BTINH2
2
T-DBTAS
2
T-RSS
2
2
N-OBT
2
2
2
S-POS
2
S-TRM
2
S-SOFT
2
Setting range
0 to 9
0
0 to 3
0
0 / 

0 /  / 2
0
S-BT
50 to 3000
200
NPS
0 / 
0
0 / 

0 /  / 2
0
NTO
0 /  / 2

0 to 6
0
0 /  / 2

0 to 359
2
0 to 500
0
0 / 
0
0 / 
0
0 to 6
0
0 / 

0 to 359
2
0 to 359
262
0 to 300
30
50 to 500
250
OBT
0 / 
0
0 to 9
4
OBTS
0 / 
0
OBTT
0 / 
0
50 to 250
70
00 to 250
70
00 to Max
70