Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for JUKI TC16
Summary of Contents for JUKI TC16
- Page 1 ENGLISH TC16 INSTRUCTION MANUAL...
- Page 2 Retain this Instruction Manual for future reference. CAUTION This Instruction Manual is intended for the TC16. To use this product when it is installed on a machine (sewing machine), make sure to read and fully understand the “IMPORTANT SAFETY INSTRUCTIONS” provided in the Instruction Manual for the machine on which this product is to be installed in advance.
-
Page 3: Table Of Contents
(3) TC16C Type for servo-motor ........................2 2. Installing the control box (for TC16A and TC16B only) ..............3 3. Replacing procedure of the cloth plate (left) when installing TC16 after setting up the sewing machine ..............................3 4. Installing the tape guide (auxiliary presser) ..................3 5. -
Page 4: Ⅰ . Specifications
Ⅰ . SPECIFICATIONS Applicable model MF-7500(D)-C11, MF-7500(D)-E11/MD11 Tape width used Max. 40 mm (finished width) Applicable motor Name of device Type TC16A With control box (220 to 440V) Clutch motor TC16B With control box (100 to 240V) SC-921 TC16C For servo-motor –... -
Page 5: Ⅱ . Installation Of The Device
Ⅱ . INSTALLATION OF THE DEVICE 1. Components of device (components packed together with a single unit of device at the time of delivery) (1) TC16A Type with control box (220 to 440V) (2) TC16B Type with control box (100 to 240V) ①... -
Page 6: Installing The Control Box (For Tc16A And Tc16B Only)
Control Box Stand 3. Replacing procedure of the cloth plate (left) when installing TC16 after setting up the sewing machine WARNING : To protect against possible personal injury due to abrupt start of the machine, be sure to start the following work after turning the power off and ascertaining that the motor is at rest. -
Page 7: Installing The Tape Cutter Unit
5. Installing the tape cutter unit WARNING : To protect against possible personal injury due to abrupt start of the machine, be sure to start the following work after turning the power off and ascertaining that the motor is at rest. 1) Install tape cutter unit ❶... -
Page 8: Tc16C (For Servo-Motor) Type
❺ ❹ ❸ ❻ ❷ A : 3P connector B : 6P connector Install knee switch ❷ on the bottom surface of the table using wood screws ❸ (SK3514000SC) supplied as accessories, and connect relay cord ❹ to control box ❻ and cutter unit ❺. 6P connector (relay cord) / control box ❻... -
Page 9: Installation And Setting Sc-921 (For Tc16C Only)
7. Installation and setting SC-921 (for TC16C only) For the details of installation of SC-921, refer to the Instruction Manual for SC-921. (1) Installing procedure 1) Referring to the Instruction Manual supplied with the ❸ SC-921, connect the SC-921 control box to the M51N motor. - Page 10 4) Adjusting the synchronizer ❺ WARNING : ❷ To protect against possible injury to hands or fingers due to abrupt start of the machine during performing adjustment, perform the adjustment of the stop position under the function setting mode. ❶ 1.
-
Page 11: Change Of The Setting
(2) Change of the setting [Adjusting procedure] 1) Turn the power OFF. 2) Pressing switch ❶, turn ON the power. ❶ 3) The screen display is as shown in the figure. (In the case the screen display does not change, re-carry out the steps of procedure 1) and 2).) Caution: If you have already set another number and data, the last number... - Page 12 5) Change type of the machine head by switch ❹ (or switch ❺). pressing Then select dL87 → MFS1 or MF. ❷ ❸ ❹ ❺ Factory-set Display of Maximum sewing Machine head sewing speed option speed sti/min sti/min MF-7500D-C11 MF-7500D-E11 MFS1 4000 5000...
-
Page 13: Ⅲ . Operation
Ⅲ . OPERATION WARNING : Do not place hands, fingers, etc. within the operating range of the tape cutter when the power is turned ON so as to prevent accidents caused by abrupt start of the sewing machine. In addition, do not use the tape cutter unit with safety cover and the like removed. Press knee switch ❶... -
Page 14: Ⅵ . Adjustment Of Components
Ⅵ . ADJUSTMENT OF COMPONENTS Standard adjustment of assembling adjustment of the tape cutter mechanism components has been performed at the time of delivery. However, when performing assembling due to the replacement of components or the like, perform the adjustment with the dimension value below. Perform the adjustment work by the maintenance engineers who are familiar with the sewing machine and trained for the safety so as to prevent accidents caused by unfamiliarity or wrong adjustment. -
Page 15: Adjusting The Angle Of The Counter Knife
2. Adjusting the angle of the counter knife WARNING : Do not place hands, fingers, etc. within the operating range of the tape cutter when the power is turned ON so as to prevent accidents caused by abrupt start of the sewing machine. In addition, do not use the tape cutter unit with safety cover and the like removed. -
Page 16: Ⅴ . Test Cut
Ⅴ . TEST CUT WARNING : Do not place hands, fingers, etc. within the operating range of the tape cutter when the power is turned ON so as to prevent accidents caused by abrupt start of the sewing machine. In addition, do not use the tape cutter unit with safety cover and the like removed. Perform the test cut of the tape cutter by the procedure below using the material for testing before entering sewing of the products.
Need help?
Do you have a question about the TC16 and is the answer not in the manual?
Questions and answers