Quantum Atlas 10K II 9.2/18.4/36.7/73.4 GB Product Manual page 368

Reservation Identification, 5-163, 5-165, 5-166, 5-191,
5-192, 5-193
RESERVE (6) Command, 5-191
RESERVE (10) Command, 5-193
Reset Condition, B-24
Response Data Format, 5-35, 5-36
Retry Count, 5-188, 5-190
Returned Logical Block Address, 5-141, 5-142
REZERO UNIT Command, 5-197
Rigid Disk Geometry Page, 5-107
Rotational Offset, 5-107, 5-109
—S—
SAVE DATA POINTER Message, B-35
SCSI Bus Conditions, B-23
SCSI Hardware Revision Number, 5-35
SCSI Message Format, B-25
SEEK (6) Command, 5-199
SEEK (10) Command, 5-201
SELECTION Phase, B-14
SEND DIAGNOSTIC Command, 5-203
Sense Data Availability, 5-171
Sense Keys, 5-175
SET DEVICE IDENTIFIER Command, 5-205
Signal Restrictions Between Phases, B-21
SIMPLE Message, B-35
SPECIFICATIONS, 4-1
Spin Up (Ultra 160/m SCSI drives with 68-Pin
Connector), 3-10
Spin Up for SCA-2 Connector Versions, 3-13
Standard Inquiry Data Page, 5-35
Starting Boundary, 5-79, 5-81
START/STOP UNIT Command, 5-207
Status Reporting, 5-172
Supplied Format, 5-161, 5-162, 2-204
Supported Additional Sense Codes, 5-179
Supported Diagnostic Page List, 5-204
Supported Page List, 5-37
Supported Sense Keys, 5-175
Supported Vital Product Data Pages Page, 5-37
SYNCHRONIZE CACHE Command, 5-209
SYNCHRONOUS DATA TRANSFER REQUEST Message, B-
36
—T—
TARGET RESET Message, B-37
TARGET TRANSFER DISABLE Message, B-37
TASK COMPLETE, B-38
TERMPWR (Ultra 160/m SCSI drives with 68-Pin
Connector), 3-8
TEST UNIT READY Command, 5-211
Track Skew Factor, 5-105, 5-106
Translate Format, 5-161, 5-162, 5-204
Translated Address (Cylinder Number), 5-161
Translated Address (Head Number), 5-161
Quantum Atlas 10K II Ultra 160/m SCSI Hard Disk Drives
—U—
Unit Attention Condition Page, 5-64
—V—
Vendor Specific, 5-136, 5-142, 5-226
Vendor Specific Bits, 5-8
Vendor-Unique Caching Page, 5-110
Verification Length, 5-209
VERIFY Command, 5-213
Verify Correction Span, 5-71, 5-72
Verify Recovery Time Limit, 5-71, 5-72
Verify Retry Count, 5-71, 5-72
Vital Product Data Pages, 5-39
—W—
WIDE DATA TRANSFER REQUEST Message, B-38
WRITE (6) Command, 5-215
WRITE (10) Command, 5-217
WRITE AND VERIFY Command, 5-219
WRITE BUFFER Command, 5-221
WRITE LONG Command, 5-223
Write Protection (Ultra 160/m SCSI drives with 68-Pin
Connector), 3-10
Write Retry Count, 5-65, 5-67
WRITE SAME Command, 5-225
WRITE SKIP MASK Command, 5-227
—X—
XDREAD (10) Command, 5-229
XDWRITE (10) Command, 5-231
XOR Control Mode Page, 5-60, 5-82
XPWRITE (10) Command, 5-233
Index
I 3