Table of Contents
Advertisement
20
Timer Recording
Follow the steps below to program
your VCR to record TV programs
while you're away from home. You
can program up to eight timer record-
ings. For each one, the VCR will turn
itself on, record, and turn itself off
automatically.
Before you begin make
sure:
• Channels have been programmed.
• The clock has been set.
• There is a tape in the VCR. Make
sure the tape's record tab is intact
and the tape is long enough to record
the program(s).
• The VCR is in VCR position.
You must do each step within 60 sec-
onds of completing the previous step.
If you don't, you will have to start
again at step 1.
1
Press the MENU button to bring up the
main menu display.
1 PROGRAM
VCR SET UP
,
NO PUSH EXIT
Press the Number 1 button on the
remote control to select PROGRAM.
SELECT
PUS. NO SH0W ' ',
ONCE
|
DAILY
1
WEEKLY
[
PROGRAM REVIEW
/
/
ND PUSH EXIT
/
3
Select a once, daily or weekly recording.
• Press the Number 1 button to select
ONCE. The VCR will record a TV
program on any day you choose, up to
12 months away.
• Press the Number 2 button to select
DAILY. The VCR will record from
Monday to Friday - starting at the
same time and for the same length of
time.
• Press the Number 3 button to select
WEEKLY. The VCR will record on
the same day, at the same time, and for
the same length of time every week.
ILY PROGI_ M
NqN-Ff]I_
ROGRAM
;:_ 1_3.4. _67_-_} Daily
/
Recording
Menu
[
SELECT PROGRAMNUMBER
]
_TO
ENDPUSH
EXIT
,
Screen
4
Use the Number
buttons
(1 - 8) to
select
a position
in which to store the timer
recording.
Flashing
numbers
indicate
an open position
(one in which a timer
recording
has not yet been stored).
NOTE:
If you select a number
that has
already been used to store a timer
recording,
PREVIOUSLY
SET PRO-
GRAM will appear on-screen
for a few
seconds.
Then information
about the
program
in that position
will be dis-
played
on-screen,
lf this happens, press
the STATUS/EXIT
button twice.
Then
start again at step 1.
5
• If you are using a standard
anlem_a
to VCR to TV hookup, enter the
channel of the TV program you warn
to record (you must enter a 0 before
all single digit channels).
• If you are recording from line input,
press O, O. A/V IN will appear on-
screen.
• If you are recording using a cable
converter box (channel 3 or 4), see
pages 40 - 41.
NE TIME PROGRAM
PROGRAM,_ _z.
CHANNEL "v r',_
]
CORRECT PUSH CLEAR/
_0
END PUSH EXIT
.J"
6
Press two Number buttons for the hour(s)
you want the recording to begin. Press
two number buttons for the minute(s)
you want the recording to begin. Press 1
for AM or 2 for PM. For example, for
9:30 PM, press 09, 30, 2.
ROGRAM
1
CHANNEL
\_0_
,ME ON _:_--
TO CORRE(_T PUSH CLEAR
END PUSH EXIT
,7
Follow the instructions in step 6 to set
the recording's stop time (AM or PM
will be set automatically).
ROGF_,M
1
HANNEL
10
ME ON
_,:30PM
,_EOPP _-'_--_,
.
_.
TO CORRECT PUSH CLEAR
_T_
END PUS H EXIT
Checking
or Clearing Timer Recordings
1. With the VCR on and in VCR
position, press the MENU button.
2. Press the Number 1 button to
select PROGRAM.
3. Press the Number 4 button to
select PROGRAM REVIEW. The
timer recording information for the
program with the lowest numbered
4.
position will appear on-screen. If
there are no timer recordings set,
nothing will happen when you press
the Number 4 button.
Press the Number 1 button repeated-
ly to re'_iew all programmed timer
recordings.
If you don't press the
Number 1 button in 10 seconds, the
.
6.
VCR will automatically display infor-
mation about the next programmed
timer recording.
This will continue
until all filled positions have been dis-
played. Then the menu will disappear.
To cancel the timer recording dis-
played, press the CLEAR button.
Repeat steps 1 - 5 to make sure you
have cleared the correct timer record-
ing.
Advertisement
Table of Contents
