Table of Contents
Advertisement
11
Setting the Clock (cont'd)
Automatic
Clock Setting
Press the MENU
button to bring up
the main menu display.
2
Press the Number
4 button
to select
SET CLOCK.
If OFF appears to the right of AUTO
CLOCK,
press the Number
1 button
once. A new display screen will appear.
If ON appears to the right of AUTO
CLOCK,
press the Number
1 button
t,
twice. A new display screen will appear. :
• If you want the VCR to locate a
local PBS station from which to
take the time, press the Number
1
button to select SET PBS CH.
AUTO.
If the current time appears
on-screen,
you're
finished.
Press the
STATUS/EXIT
button to exit.
NOTE." CANNOT
FIND PBS
CLOCK
DATA may flash
on-screen.
:
In this case,
tell the VCR the PBS
!
station from which to take the time.
!
O If you want to tell the VCR the
!
PBS station
from which
to take
:
the time, press the Number
2 but-
ton to select SET PBS CH. MANU-
:
AL, then use the Number
buttons
to "
select the channel
number
of the
:
desired PBS station.
If the current
:
time appears
on-screen,
you're fin-
:
ished. Press the STATUS/EXIT
but- :
ton to exit.
NOTE:
CANNOT
FIND PBS
i
CLOCK
DATA may flash
on-screen.
:
In this case, press the Number
1
i
button to choose SELECT
NEW
:
PBS CH., then use the Number
but-
tons to select the channel
number
of _
another
PBS station.
Or, press the
Number
2 button to select SET PBS
CH. AUTO,
then go to step 5.
5
Turn the VCR power off, and leave it
off for several minutes. When you turn
the VCR back on, the time will be set.
Remote Control
Number
Buttons
.
STATUS/EXIT
Button
REW_EARCH
FF
H
®
li+++
+ +
®Fe--
_S_UTrLE
STATU,_×II
¢tEAgl
o
C_D
@---
--
MENU Button
--
CLEAR Button
• To reset the clock, follow
the steps on page
10 or page 11.
• To display the time, press the STATUS/EXITbutton.
A status display,
which
includes the time, will appear on the TV screen for about five seconds.
For
details,
see "On-Screen
Displays"
on page 12.
• If you press the STATUS/EXIT
button
while you are setting
the clock, the TV screen
will return to the program
you were watching.
If this happens,
start over
• To cancel the Daylight-Saving
Time, follow
steps 1 - 2 under "Daylight-Saving
Time Selection"
on page 10. At step 3, press the Number 3 button so that OFF
appears
to the right of DAYLIGHT
SVG TIME.
Press the STATUS/EXIT
button to
exit.
For Manual
Clock Setting
• To make corrections
while you are setting the clock manually, press the CLEAR
button until the space for the number
you want to correct is flashing.
Then enter
the correct number.
• If the numbers
entered
do not match the VCR's internal
calendar,
the entry will be
rejected and a question
mark (?) will appear on the TV screen.
• Power failures
that last for more than one minute can cause you to lose your clock
setting
when you use the VCR with the auto clock function
set to OFF. If this hap-
pens, follow
the steps on page 10.
For Automatic
Clock Setting
• If TV has been selected at the TUNER SET UP menu, you can select channels
2 -
69 at step 4 under "Automatic
Clock Setting."
If CABLE
TV has been selected
from the TUNER SET UP menu, you can select channels
1 - 125 at step 4 under
"Automatic
Clock Setting."
See page 27for
details.
• If you select SETPBS
CH. AUTO at the AUTO CLOCK menu, you cannot manual-
ly select the PBS channel from which you want the VCR to take the time.
• If the clock still is not set when you turn the VCR back on at step 5 under
"Automatic
Clock Setting,"
set the clock manually.
• The clock cannot be set automatically
if you don't receive a channel
that carries a
time signal in your area.
If this is the case, set the clock manually.
• If there are only a few channels
in your area that carry time signals,
setting
the
clock automatically
may take several
minutes.
If nothing
happens
even after you
wait several minutes,
set the clock manually.
Advertisement
Table of Contents
