Table of Contents
Advertisement
20
Timer Recording
Follow the steps below to program
your VCR to record TV programs
while you're
away from home.
You
can program
up to eight timer record-
rags.
For each one, the VCR will turn
itself on, record,
and turn itself off
automatically.
Before you begin make
sure:
Channels
have been programmed.
_The
clock has been set.
t_There
is a tape in the VCR. Make
sure the tape's record tab is intact
and the tape is long enough
to record
the program(s).
_The
VCR is in VCR position.
You must do each step within 60 sec-
onds of completing the previous step.
If you don't, you will have to start
again at step 1.
Press the MENU
button to bring up the
main menu display.
TO'_'_ESELE
CT PUSH GO. SROWN_
I PROGRAM
2 VCR SET UP
3 TUNER SET UP
4 SET CLOCK
2
Press the Number
I button on the
remote
control to select PROGRAM.
TO SELECT PUSH NO SHOWWN_
I ONCE
2 DAILY
3 WEEKLY
4 PROGRAM REVrEW
_D
PUSH EXIT
%
.
Select a once, daily or weekly recording.
'_ Press the Number
1 button to select
ONCE.
The VCR will record
a TV
program
on any day you choose,
up to
12 months
away.
Press the Number
2 button
to select
DALLY. The VCR will record from
Monday
to Friday - starting at the
same time and for the same length of
time,
Press the Number
3 button
to select
WEEKLY.
The VCR will record
on
the same day, at the same time, and for
the same length of time every week.
io o o loay
PROGRAM
.12345676.
Recording
Menu
SELECT PROGRAM NUMBER
Screen
ENDPUSH EXIT
Use the Number
buttons
(1 - 8) to select
a position
in which to store the timer
recording.
Flashing
numbers
indicate
an open position
(one in which a timer
recording
has not yet been stored).
NOTE:
(f you select a number
that has
already
been used to store a timer
recording,
PREVIOUSLY
SET PRO-
GRAM will appear on-screen
for a few
seconds.
Then it!formation
about the
program
in that position
will be dis-
played
on-screen.
If this happens,
press
the STATUS/EXIT
button
twice.
Then
start again at step I.
If you are using a standard
antenna
to VCR to TV hookup,
enter the
channel
of the TV program
you want
to record (you nmst enter a 0 before
all single digit channels).
If you are recording
from line input.
press 0, 0. A/V IN will appear on-
selden.
"° If you are recording
using a cable
converter
box, see pages 34 - 35.
PROGRAM
1
CHANNEL
- -
[O CORRECT PUSHCLEAR
O END PUSH EXIT
Press two Number buttons for the hour(s)
you want the recording
to begin.
Press
two number
buttons for the minute(s)
you want the recording
to begin.
Press 1
for AM or 2 Ibr PM,
For example,
for
9:30 PM, press 09, 30. 2.
ONE TIME PROGRAM
PROGRAM
1
CHANNEL
10
TIME ON
P
- -
TO CORRECT PUSH CLEAR
END PUSH EXIT
Follow the instructions
in step 6 to set
the recording's
stop time (AM or PM
will be set automatically).
ONET_ME PROGRAM
_'_
_ROGRAM
I
J
CHANNEL
10
TIME ON
0930 PM
TIME OFF
--
-
lO CORRECT PUSH CLEAR
END PUSH EXIT
Checking
or Clearing Timer Recordings
1. With the VCR on and in VCR
posili(m,
press the MENU
button.
2. Press the Number
1 btttlon to
select PROGRAM.
3. Press the Nmnber
4 bumm to
select PROGRAM
REVIEW.
The
timer recording
information
fur the
progranl
with the h_west numbered
position
will appear un-screen.
If
there are no timer recordings
set,
noflfing will happen
when you press
the Number
4 button.
4.
Press the Number
1 button
repeated-
ly to review all programmed
timer
recordings.
If you don't press the
Number
I button
in 10 seconds,
the
5.
6.
VCR will autumatically
display
inl;m-
mation
about the next programmed
timer recording.
This will continue
until all filled positions
have been dis-
played.
Then the menu will disappear.
To cancel the timer recording
dis-
played, press the CLEAR
bumm.
Repeat steps I - 5 to make sure you
have cleared
the correct timer record-
ing.
Advertisement
Table of Contents
