Table of Contents
Advertisement
20
Timer Recording
****'°°°_QoQ*oo*''''QIe*ee''_titoe***_'_oo_°'*'°°°°6°_°_°*_°_'_*_°6_'***_°_°_*o_°_*o_°°°_o'oeo°°_°_**
Follow the steps below to progranl
your VCR to record TV programs
while you're away fi'om home.
You
can program
up to eight timer record-
ings.
For each one, the VCR will turn
itself on, record,
and turn itself off
automatically.
Before you begin make
sure:
Channels
have been programmed.
The clock has been set.
There is a tape in the VCR (make
sure the tape's record
tab is intact
and the tape is long enough
to record
the program(s).
The VCR is in VCR position.
You must do each step within 60 sec-
onds of completing the previous step.
If you don't, you will have to start
again at step 1.
Press the MENU
button to bring up lhe
main menu display.
OT
us o
coo-vo--
E st s S TSE
U u U OW;
Press the Number 1 button on the
remote control to select PROGRAM.
432T@1
WEEKLYONCEDAILYPROGRAM
ENDSELECT
PUSH PUSH
REVIEW
MENU N O SHOW 1
Select a ONCE,
L)AILY or WEEKLY
recording.
Press the Number
I button to select
ONCE.
The VCR will record
a TV
program
on any day you choose,
up
it)
12 months
away.
Press the Number
2 button to select
DALLY. The VCR will record from
Monday
to Friday - starting
at the
same time and for the same length of
time.
Press the Number
3 button
to select
WEEKLY.
The VCR will record
on
the same day, at the same time, and
for the same length every week.
IA,LY PROGRAM
IMON-ER,_"'_ D aily
ROGRAM
-1234567811
ScreenMennRec°rding
Use the Number
buttons
(1 - 8) to select
a position
in which to store the timer
recording.
Flashing
numbers
indicate
an open position
(one in which a timer
recording
has not yet been stored).
NOTE: If you select a number
that has
already been used to store a timer
recording,
PREVIOUSLY
SET PRO-
GRAM will appear on-screen
for a few
seconds.
Then information
about the
program
in that position
will be dis-
played
on-screen,
lf this halv)ens,
press
the MENU button twice.
Then start
again at step I.
If you arc using a standard
antenna/cable
to VCR to TV hookup,
enter the channel
of the TV program
you want to record (you must enter a
0 before all single digit channels).
If you are recording
from line input,
press O, O. A/V IN will appear on-
screen.
If you are recording
using a cable
converter
box, see pages 37 - 38.
OloT
o
PROGRAM
1
CHANNEL
TO CORRECT
PUSH CLEAR
END PUSH MENU
Press two Number buttons
lor the
hour(s) you want the recording to begin.
Press two number buttons
for the
minute(s)
you want the recording
to
begin.
Press 1 for AM or 2 for PM.
For
example,
for 9:30 PM, press 09, 30, 2.
O_E
TIME PROGRAM
1
PROGRAM
1
CHANNEL
10
TIME
ON
2 : _.
TO CORRECT
PUSH CLEAR
END PUSH
MENU
j
Follow
the instructions
in step 6 to set
the recording's
stop time (AM or PM
will be set automatically).
i o1
PROGRAM
1
CHANNEL
10
TIME
ON
09:30 PM
TIME
OFF
-.:-
O CORRECT
PUSH
CLEAR
,,.To
us, ENu
!_ 1. With the VCR on and in VCR
position, press the MENU button.
Press the Number 1 button to
4,
select PROGRAM.
'!_: 3 . Press the Number 4 button to
select PROGRAM REVIEW. The
;
timer recording information for the
program with the lowest numbered
position will appear on-screen.
Press the Number 1 button repeated-
ly to review all programmed timer
recordings.
If you don't press the
Number I button, in ten seconds the
VCR will automatically display
pro-
grammed timer recording. This will
continue until all filled positions
have been displayed,
Then the pre-
wous on-screen
menu will appear,
5. To cancel
the timer recording
dis-
played,
press the CLEAR
button.
6. Repeat
steps 1 - 5 to make sure you
have cleared the correct position.
Advertisement
Table of Contents
