Burner Caps And Heads - GE P2B930 Owner's Manual And Installation Instructions

Care and cleaning of the range,
Burner cap is Burner cap is
properly seated. NOTproperly
seated.
Burner heads on Some models
The burner heads (on some models)
are removable, Simp!_ lift them aft
the range for cleaning,
head (on some models)
Burner head
_\, ")
Burner base o()o_
Make Surethe ringTntt_eburner head
is positionedoverthe electrodeand
thatthe burner head isfu!ly inserted
insi@ the burner base.A Smal!gap
between the baseand head is no_a !
Front-right head (On Some models),
front-left h ead, back-right head and
backdeft head
Sta
ing
_i_ needleor t_vist:tie
Burner(k._ -_,,_..)) to unclogthe
• "_'_ smallholeinthe
bUS e''_ Electrode burner head:
Make Surethe Slot in the burner head
iSpOSitioned0Ver the electrode,
Hole in
head
The oval burner head/cap assemblyis
removable_ Simplylift it offthe range for
cleaning Usea sewingneedb or twistTtie
to Unclogthe smallhole inthe bUmer
heads,
30
Burner Caps, Bases and Heads
Beforeremoving the burner caps and headsIon
some models),remember their sizeand location.
Replacethem in the same location after cleaning.
NOTE:Do not usesteel wool or scouring
powders to clean the burner parts.
Burner caps
Lift off when cool. Wash burner caps in hot,
soapy water and rinsewith clean water. You
may scour with a plastic scouring pad to
remove burned-on food particles. To get rid of
burned on food, place the caps in a covered
container. Add 1/4 cup ammonia and let soak
for several hours or over night. Wash, rinse well
and dry.
Tri-ring burner (onsome models)
The outer cap on the tri-ring burner is not
removable. Only the center round cap may be
removed for cleaning.
Tocleanthe burner bases,usesoapy water and a
plasticscouringpad.Wipe cleanwith a damp cloth.
Make sure that no water gets into the burner
bases.Allow them to dry fully before using.
Burner Heads (on some models) and Oval
(Center) Burner Head/Cap Assembly
The burner heads and the oval burner head/cap
assembly are removable. Simply lift them off the
range for cleaning.
For proper ignition, make sure the small hole in
the section that fits over the electrode is kept
open. A sewing needle or wire twist-tie works
well to unclog it.
The slits in the burner heads must be kept clean
at all times for an even, unhampered flame.
Clogged or dirty burner ports or electrodes will
not allow the burner to operate properly.
Any spill on or around an electrode must
be carefully cleaned. Take care to not hit an
electrode with anything hard or it could be
damaged.
Clean the burner heads routinely, especially
after bad spillovers, which could clog the
openings. Lift off when cool.
To remove burned-on food, soak the burner
heads in a solution of mild liquid detergent
and hot water for 20-30 minutes. Formore
stubborn stains, use a toothbrush.
After cleaning
Beforeputting the burner caps,heads (onsome
models)and oval head/cap assembly back,shake
out excesswater and then dry them thoroughly
by setting in a warm oven for 30 minutes.
Replacement Burner Heads (onsome models)
Replace burner heads over the electrodes on
the cooktop, in the correct locations according
to their size.There is one small, one medium,
one large and one extra-large burner head.
Makesurethe s,o_ or no_edependingon model
_neourner headispositionedover_ne elec_roae.
ode __S at or
E ectr
4ole
:_roae
Oval (Cented Burner Head/Cap Assembly
ReD,ace _ neova center)neaa/caD assemD,y over
the electrodeon _neCOOKl:Op.
Oval
neaa and
CaD
assemE.,
0
Front of ranoe
MaKe sure me sic [ In me
burner nead is oositioned
over l:ne electrode.
°/
Elec_roae
Caps
ReD,ace t he matchingsizeCaDS onto _neDurner
Doses o r
heads
Hakesurethat the headson somemodels ana
capsare replacedin _necorrec_ loca_lons
0
. o
_ _ome models)
Front of range Trlmng caF
on some
models