Burner Caps And Heads - GE Appliances P2B930 Owner's Manual And Installation Instructions

Care and cleaning of the range,
Burner cap is Burner cap is
properly seated. NOTproperly
seated.
Burner heads (on Some models/
The burner heads (on some models/
are removablel Simply lift them off
the range for C eaning,
Tri-ring head (on some models)
Burner head
EleCtrode
Buiner base _
MaResure the ring in the burne_head
is positionedoverthe electrodeand
thatthe burner head isfully inserted
inside the burner base.A smallgap
between the baseand head is normal.
Front-right head (on some models),
front-left head, back-right head and
back-left head
Burner head
Stability nber usea sewing
].-"_i_ needle o rtwist-tie
auiner(k. "_S) tounclog t he
, ' '_._lp_-_ small hole inthe
0ase'v _ Electrodeburnerhead
Hake sure the slot in the burner head
is positioned over the electrode
Hole in
• burner
ead
The Ovalburner head/cup assemblyiS
removable Simplylift it off the rangefor
cleaning Used Sewingneedleor _ist-tie
to unclog the smallhole inthe burner
heads.
30
Burner Caps, Bases and Heads
Beforeremoving the burner caps and heads(on
some models),remember their sizeand location.
Replacethem in the same location after cleaning.
NOTE:Do not usesteel wool or scouring
powders to clean the burner parts.
Burner caps
Lift off when cool. Wash burner caps in hot,
soapy water and rinsewith clean water. You
may scour with a plastic scouring pad to
remove burned-on food particles. To get rid of
burned on food, place the caps in a covered
container. Add 1/4 cup ammonia and let soak
for several hours or over night. Wash, rinse well
and dry.
Tri-ring burner (onsome models)
The outer cap on the tri-ring burner is not
removable. Only the center round cap may be
removed for cleaning.
Tocleanthe burner bases,usesoapy water and a
plasticscouringpad.Wipe cleanwith a damp cloth.
Hake sure that no water gets into the burner
bases.Allow them to dry fully before using.
Burner Heads (on some models) and Oval
(Centefl Burner Head/Cap Assembly
The burner heads and the oval burner head/cap
assembly are removable. Simply lift them off the
range for cleaning.
For proper ignition, make sure the small hole in
the section that fits over the electrode is kept
open. A sewing needle or wire twist-tie works
well to unclog it.
The slits in the burner heads must be kept clean
at all times for an even, unhampered flame.
Clogged or dirty burner ports or electrodes will
not allow the burner to operate properly.
Any spill on or around an electrode must
be carefully cleaned. Take care to not hit an
electrode with anything hard or it could be
damaged.
Clean the burner heads routinely, especially
after bad spillovers, which could clog the
openings. Liftoff when cool.
To remove burned-on food, soak the burner
heads in a solution of mild liquid detergent
and hot water for 20-30 minutes. For more
stubborn stains, use a toothbrush.
After cleaning
Beforeputting the burner caps,heads (on some
models)and oval head/cap assembly back,shake
out excesswater and then dry them thoroughly
by setting in a warm oven for 30 minutes.
Replacement Burner Heads (onsome models)
Replace burner heads over the electrodes on
the cooktop, in the correct locations according
to their size.There is one small, one medium,
one large and one extra-large burner head.
"1
Front of range onsorn_'mod_es
Tri-ring head
Hake sure the slot or no_e depending on "nOdel
me burner head
is
positioned over the electrode.
Electrode __S at or
Oval (Centerl Burner Head/Cap Assembly
ReD,ace m e ova center)neaa/caD assemD,y over
the electrode on tne COOKtOp.
Oval head and cap
asjly
Front of ranoe
Hake sure the slot in the
burner heac is positioned
o\er me electrode.
Electrode
Caps
Reolace the matchingsizecadsonto me burner
bases or
heads
Hakesurethat the headson somemoaels ana
capsare replacedin tne correct
locations
0
mem
Front of range Tri-nng cap
0
on some models}