Gui (Graphical User Interface) Transfer (Copying) (Vhs L Dvd) - Panasonic Diga DMR-ES35V Operating Instructions Manual

Transfer (Copying)
∫ GUI (Graphical User Interface)
Transfer (Copying) (VHS l DVD)
[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW]
You can transfer (copy) programmes recorded on a video cassette onto a
¢
disc from the location of playback as of the transfer (copying) start of the
tape.
¢
When you set the recording mode to "FR" (l right) and "Time Setting"
to "Off" (l right), you can transfer (copy) the whole tape from the
beginning to the end.
Preparation
≥Select the unit viewing channel (e.g. AV input) on the TV.
VHS (Recording source)
≥Press [DRIVE SELECT] to select the VHS.
≥Insert the video cassette containing the programme to be copied.
(l 17)
≥Press [1, PLAY] to play the video cassette and then press [AUDIO] to
select the audio type you wish to record.
≥Stop the tape at the position where you wish to start recording.
DVD (Recording target)
≥Press [DRIVE SELECT] to select the DVD.
≥[RAM] Release protection. (disc l 55, cartridge l 55)
≥Insert a disc and confirm there is sufficient empty space for recording
on it. (l 17, 36)
≥Select the recording mode. (l 18)
Settings (l 59, TV System)
≥When transferring (copying) an NTSC tape to a DVD
- Set "TV System" on "Connection" in Setup to "NTSC".
Be certain that the inserted disc only contains NTSC video contents.
≥When transferring (copying) a PAL tape to a DVD
- Set "TV System" on "Connection" in Setup to "PAL".
Be certain that the inserted disc only contains PAL video contents.
[1]
Press [DRIVE SELECT] to select the VHS.
[2]
While both DVD and VHS are stopped
Press [FUNCTIONS].
[3] Press [3, 4] to select "Copy" and then press
[ENTER].
[4]
Set the transfer (copying)
direction.
≥Set "Source" to "VHS".
≥If you are not going to change the
transfer (copy) direction, press [4]
and skip to step 5.
∫ To change the setting
(1) Make sure "Copy Direction" is selected and press [1].
(2) Make sure "Source" is selected and press [ENTER].
(3) Press [3, 4] to select "VHS" and then press [ENTER].
≥ When you set "Source" to "VHS", "DVD" is automatically
selected in "Destination".
(4) Press [2].
(5) Press [4].
[5]
Set the recording mode.
≥If you are not going to change the
recording mode, press [4] and skip
to step 6.
∫ To change the setting
(1) Make sure "Copy Mode" is selected and press [1].
(2) Make sure "Recording Mode" is selected and press [ENTER].
(3) Press [3, 4] to select the recording mode (XP, SP, LP, EP or FR)
and then press [ENTER].
≥ About FR mode (l right)
(4) Press [2].
(5) Press [4].
46
RQTV0136
[6]
Set the time limit.
≥If you are not going to change the
recording time, press [4] and skip to
step 7.
∫ To change the setting
(1) Make sure "Copy Time" is
selected and press [1].
(2) Make sure "Time Setting" is selected and press [ENTER].
(3) Press [3, 4] to select the time setting ("On" or "Off") and then
press [ENTER].
≥ When you select "Off", proceed to Step (6) below.
(4) Press [4] to select "Copy Time" and then press [ENTER].
(5) Press [2, 1] to select "Hour" and "Min." and press [3, 4] to set
the recording time and then press [ENTER].
≥ You can also set the time with the numbered buttons.
≥ Maximum recording time is 8 hours.
(6) Press [2].
(7) Press [4].
[7]
Make sure "Start Copying"
is selected and press
[ENTER].
≥The confirmation screen appears.
[8]
Press [2] to select "Yes"
and then press [ENTER].
[-R] [-R]DL] [-RW‹V›] [+R] [+R]DL]
Press [2, 1] to select
"Copy & Finalize" or "Copy
Only" and then press
[ENTER].
≥Transfer (copying) starts.
≥Transfer (copying) is automatically
stopped when the tape reaches the
end, the remaining capacity of the
disc is filled or when a timer recording starts. (A message appears on
the TV screen and then disappears a few seconds later.)
≥If "Copy & Finalize" is selected;
After finalizing, the disc becomes play-only and you can play
them on other DVD equipment.
However, you can no longer record or edit.
≥Finalizing will not start if copying is not completed (e.g., due to
shortage of remaining disc space).
∫ To stop transfer (copying) in the middle (process)
Press and hold [RETURN] for about 3 seconds or more.
≥However you cannot stop finalize after it has started.
∫ About FR mode
When "Time Setting" is set to "Off" in step 6 above:
≥The recording mode is automatically selected by estimating the
remaining capacity of the disc for transfer (copying) of only the
recorded parts in the video cassette (unrecorded parts will not be
recorded).
≥When you press [ENTER] to start transfer (copy), the tape is
automatically fast-forwarded to the end and then fast-rewound to the
beginning before the transfer (copying) is actually started. It may take
time to start transfer (copy). If the remaining capacity of the disc is
insufficient, the transfer (copying) will be stopped in the middle.
≥The recording is divided into titles every time the tape index signals
are detected.
When "Time Setting" is set to "On" in step 6 above:
≥The recording mode is automatically determined by estimating the
remaining capacity of the disc for transfer (copying) of the contents
equivalent to the recording time set from the start point of the transfer
(copying) on the video cassette (unrecorded parts will also be
recorded).
≥The recording is not divided into titles.
Finalizing is to enable the disc to be played on
other DVD players.