Aux2 Input; Lip.sync; Basic Operation (Tuner); Listening To The Tuner - Marantz SR5500 User Manual

1.
Select a desired Video source to decide the
routed video signal to the Monitor Outputs .
2.
Press the 7.1 CH INPUT button on the front
panel or press 7.1 CH IN on the remote to
switch the 7.1 channel input.
3.
If it is necessary to adjust the output level of
each channel, press the CH.SEL button on
the remote.
Adjust the speaker output levels so that you
can hear the same sound level from each
speaker at the listening position. For the front
left, front right, center, surround left, surround
right and surround back speakers, the output
levels can be adjusted between –10 to +10 dB.
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
4.
Adjust the main volume with the MAIN
VOLUME knob or the VOL buttons on the
remote.
To cancel the 7.1 CH. INPUT setting, press the 7.1
CH INPUT button on the front panel or press 7.1
CH IN on the remote.
Notes:
• When the 7.1 CH. Input is in use, you may not
select a surround mode, as the external decoder
determines processing.
• In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.

AUX2 INPUT

If you don't need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio
source to AUX2 as other audio input terminals.
AV SURROUND RECEIVER SR5500
INPUT SELECTOR
DISP MULTI AUTO
SLEEP AUTO SURR
SURROUND PURE SIMP
MODE DIRECT SET
MULTI M. SPEAKER B
STANDBY
AUTO HT-EQ MEN
POWER ON/OFF PHONES

LIP.SYNC

Depending on the image device (TV, monitor,
projector, etc.) connected to the SR5500, a time
lag can occur between image signal processing
and audio signal processing. Though minor, this
time lag can interfere with movie and music
enjoyment. The LIP.SYNC feature delays the
audio signal with respect to the image signal
output from the SR5500 to correct the time lag
between the sound and image. It can be operated
with the "LIP.SYNC" and and cursor buttons of
the remote controller. Set the remote controller to
the AMP mode before operating the LIP.SYNC
feature. The initial setting is OFF (0 ms).The time
lag can be adjusted in 10 ms steps up to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
Note:
• The LIP.SYSNC feature turns OFF (0 ms) in the
PURE DIRECT mode. When the PURE DIRECT
mode is deactivated, the set value of the
LIP.SYSNC feature is automatically restored.
BASIC OPERATION
(TUNER)

LISTENING TO THE TUNER

Frequency scan step for AM is selectable.
Default setup is 9 kHz step, if your country's
standard is 10 kHz step, Press TUNER button on
the remote more than 6 seconds. Scan step will
change.
Note:
• Preset memory for the tuner will clear by changing
this setup.
AUTO TUNING
TV VCR1 DSS/VCR2
2. 1.
1. TUNER CD TAPE
AUX1 AMP
TV
VOL. SLEEP MUTE
SURROUND
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ATT ANALOG
DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MT X 6.1 EQ DIGITAL
L C R
AAC PCM LFE
SL S SR
DOWN CLEAR MEMO A/D P.SCAN/V OFF
0
CHANNEL/SKIP
ND PURE SIMPLE
DIRECT SETUP DISPLAY MEMORY CLEAR
M
2. BASS TREBLE
TUNE/SEARCH
ENTER
HT-EQ MENU EXIT BAND T-MODE
T-MODE RDS
INPUT/DISC+ AUDIO SUB-T/ATT
(Using the SR5500)
1.
To select tuner and desired band (FM or AM),
press the BAND button on the front panel.
2.
Press the or cursor buttons on the front
panel for more than 1 second to start the auto
tuning function.
3.
Automatic searching begins then stops when
a station is tuned in.
(Using the remote control unit)
1.
To select tuner and desired band (FM or AM),
press the TUNER button twice within in two
seconds on the remote.
2.
Press the 5 5 5 5 5 or 6 6 6 6 6 for more than 1 second on
the remote.
3.
Automatic searching begins then stops when
a station is tuned in.
If tuning does not stop at the desired station, use to
the "Manual tuning" operation.
MANUAL TUNING
2. 1.
1.
SURROUND
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ATT ANALOG
DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MTX 6.1 EQ DIGITAL
L C R
AAC PCM LFE
SL S SR DOWN
ND PURE SIMPLE
DIRECT SETUP DISPLAY MEMORY CLEAR
M
ENTER
HT-EQ MENU EXIT BAND T-MODE 2.
(Using the SR5500)
1.
To select tuner and desired band (FM or AM),
press the BAND button on the front panel
2.
Press the or cursor buttons on the front
panel to select the desired station.
(Using the remote control unit)
DVD
1.
To select tuner and desired band (FM or AM),
CDR/MD
press the TUNER button twice within in two
seconds on the remote.
MAIN
VOL.
2.
Press the 5 5 5 5 5 or 6 6 6 6 6 on the remote to tune in the
desired station.
DIRECT FREQUENCY CALL
F.DIRECT
PTY
PURE DIRECT
3.
POWER
TV VCR1 DSS/VCR2 DVD
1. TUNER CD TAPE CDR/MD
AUX1 AMP
2.
TV MAIN
VOL. SLEEP MUTE VOL.
INPUT/DISC+
OSD MENU
1.
To select tuner and desired band (FM or AM),
press the TUNER button twice within two
seconds on the remote.
2.
Press the F.DIRECT on the remote, display
will show "FREQ - - - -".
3.
Input your desired station's frequency with the
numeric buttons on the remote.
4.
The desired station will automatically be
tuned.
TV VCR1 DSS/VCR2 DVD
TUNER CD TAPE CDR/MD
AUX1 AMP
TV MAIN
VOL. SLEEP MUTE VOL.
CLEAR MEMO A/D P.SCAN/V OFF
0
CHANNEL/SKIP
BASS TREBLE
TUNE/SEARCH
T-MODE RDS F.DIRECT
INPUT/DISC+ AUDIO SUB-T/ATT PTY
AUTO DTS
1 2 3
NIGHT CSII EX/ES VIRTUAL
4 5 6
DISPLAY MCH-ST STEREO 7.1CH IN
7 8 9
CLEAR MEMO A/D P.SCAN/V-OFF
0
CHANNEL/SKIP
BASS TREBLE TUNE/SEARCH
T-MODE RDS F.DIRECT
AUDIO SUB-T/ATT PTY
CH.SEL LIP.SYNC
SYSTEM REMOTE CONTROLLER
29