Names Of Controls And Indicators - Marantz PM-17mk II User Manual

NAMES OF CONTROLS AND INDICATORS

(Figure 2)
A
GND (GROUND) terminal
Connect the grounding wire from the Analog turntable to this
terminal.
B
MM/MC SELECTOR switch
When the INPUT SELECTOR is set to PHONO, the type of
cartridge used on the turntable can be selected between MM
(Moving Magnet) and MC (Moving Coil) using this switch.
Set this switch according to the cartridge used on the turntable.
MM (Moving Magnet)
Set the switch to the out
MC (Moving Coil)
set the switch to the in ( )position.
C
PHONO INPUT jacks
Connect the output jacks of the Analog turntable to these jacks.
D CD PLAYER INPUT jacks
Connect the output jacks of a Compact Disc player to these
jacks.
E
LINE 1 – LINE 3 INPUT jacks
These are LINE 1 – LINE 3 input jacks which can be used to
connect the audio outputs of AV components such as TV mul-
tiplex/stereo audio turners, VCRs, and leaserdisc players.
F CD-R IN/OUT jack
Connect the line output jacks and line input jacks of CD re-
corder to these jacks.
G
TAPE IN/OUT jacks
Connect the play (output) jacks and record (input) jacks of
tape decks to these jacks.
H
PRE OUTPUT terminal
Output jack for connection to extension power-amp, mixer or
similar.
I
MAIN IN jacks
Connect the pre output jacks of your pre-amp to these jacks at
the SEPARATE position of the selection switch J.
J
SEPARATE/COUPLED selection switch
The initial setting of the selection switch is COUPLED position.
This unit is possible to use integrated-amp at the COUPLED
position.
Set according to the SEPARATED position, this unit is pos-
sible to use pre-amp or power-amp.
K
SPEAKER Terminals
Connect your speaker system to these terminals.
)position.
L
REMOTE CONTROL BUS terminals
(REMOTE CONT. BUS)
By connecting this unit with a MARANTZ component equipped
with the remote control (D-BUS) jacks, both components can
be remote controlled as a system.
For details of the remote control function, read the owner's
manual of the connected component.
The bus OUT terminal is used to send signals to another item
of equipment. The bus IN terminal is used to receive signals
from another item of equipment.
M
AC IN jack
Connect to AC power outlet.
This unit can be powered by 230V AC only.
q
INPUT SELECTOR switch
Selects the program source to be produced, from PHONO,
CD, LINE 1, LINE 2, LINE 3,CD-R and TAPE.
w
VOLUME control
Turn the knob to adjust the volume. Turning the knob clock-
wise ( ) to increase the volume. The volume up-down opera-
tions can also be controlled from the provided remote control
unit.
e
PHONES jack
This jack accepts the standard stereo phone plug of head-
phones.
r
REC SELECTOR switch
Selects the COPY mode between CD recorder and TAPE deck,
or the signal to be output to the OUT jacks of CD-R and TAPE.
t
SPEAKERS switch
Press to switch the speaker systems ON (pressed-in position)
and OFF (out position).
Set the switch to OFF (out position) when you listen through
headphones only.
y
IR SENSOR
The unit receives the infrared remote control signal through
this window. Point the transmitter of the remote control unit to-
ward this window to send correct remote control signals.
u
POWER switch
Press to turn power ON and press again to turn it OFF.
Meter !1 lights up when the POWER is turned ON. The pointer
LED of the INPUT SELECTOR switch q also lights when the
power is ON and goes out when it is OFF.
i
Tone (BASS, TREBLE) controls
Turn the knobs to adjust the tone. Turning a knob controls the
level of the corresponding frequency range. Turning each con-
trol toward "+" boosts the corresponding frequency range and
toward "– " attenuates it.
TREBLE: Controls the tone of high frequencies.
BASS: Controls the tone of low frequencies.
4