Whirlpool ACE184XR0 Use & Care Manual page 13

Power Saver--Fan runs only when cooling is needed. You
can select the fan speed by pressing FAN SPEED.
Because the fan does not circulate the room air
continuously, less energy is used, but the room air is not
circulated as often. Use Power Saver when you are
asleep or away from home.
MODE
0 0 0 0
Auto Cool FanOnly Power
Saver
Fan Speed
NOTE: The Fan Speed button will operate only when Cool, Fan
Only or Power Saver mode has been selected.
1. Press FAN SPEED until you see the indicator light come on
for the setting you desire.
2. Choose Turbo, High or Low.
NOTE: After 3 seconds, Set indicator light will turn oft, and
Room indicator light will turn on. Display will show the current
room temperature.
To change the temperature display from °F to °C:
1. Turn oft the air conditioner.
2. While the air conditioner is oft, press and hold down the
MODE and FAN SPEED buttons while pressing POWER to
turn on the air conditioner.
NOTE: Follow these same steps to change the temperature
display from °C to °E
Timer delay
To set the Timer for a 1- to 24-hour delay until the air
conditioner turns off (the air conditioner must be On):
1. Press TIMER. Timer indicator light will flash. Hour indicator
light will turn on, and display will show remaining hours
before air conditioner will turn off.
Turbo r_]
s;°0°0d@H'01 I
LowU
Filter Monitor
1. When Filter indicator light is lit or flashing, remove, clean and
replace air filter. See "Cleaning the Air Filter."
2. Press and hold FILTER for 3 seconds after cleaning and
replacing the air filter. This resets the Filter Monitor.
FILTER
Hold to Reset
©
NOTE: After 360 hours of fan operating time, the Filter indicator
light will turn on. It will remain on for 180 hours or until you press
FILTER. After 180 hours, it will flash. It will continue flashing until
you press FILTER.
Temperature
Press the plus button to raise the temperature. Room
indicator light will turn oft, and Set indicator light will turn on.
Display shows the Temperature control setting. Each time you
press or hold the plus button, the temperature will increase
1° until it reaches 86°F (30°C).
NOTE: After 3 seconds, Set indicator light will turn off, and
Room indicator light will turn on. Display will show the current
room temperature.
Press the minus button to lower the temperature. Room
indicator light will turn off, and Set indicator light will turn on.
Display shows the Temperature control setting. Each time you
press or hold the minus button, the temperature will decrease
1° until it reaches 64°F (18°C).
Timer
©
2=
3.
Press the plus or minus button to adjust the delay time (1 to
24 hours).
Press TIMER again or wait 10 seconds. Timer indicator light
will remain on. Hour indicator light will turn off, and Room
indicator light will turn on. Display will show the current room
temperature.
To set the Timer to turn on the air conditioner, keeping
previous settings:
1. Turn off air conditioner.
2. Press TIMER. Timer indicator light will flash. Hour indicator
light will turn on, and display will show remaining hours
before air conditioner will turn on.
3. Press the plus or minus button to change delay time (1 to
24 hours).
4. Press TIMER again or wait 10 seconds. Timer indicator light
will remain on. Hour indicator light will turn off, and Room
indicator light will turn on. Display will show current room
temperature.
To set the Timer to turn on the air conditioner, changing
the previous settings:
1. Turn on air conditioner.
2. Adjust Mode to Auto, Cool, Fan Only, or Power Saver.
NOTE: For Auto mode, go to Step 4.
3. For Cool, Fan Only or Power Saver mode, adjust FAN SPEED
to Turbo, High or Low.
4. Adjust temperature between 64°F (18°C) and 86°F (30°C).
5. Wait 3 seconds before turning oft air conditioner.
6. Press TIMER. Timer indicator light will flash. Hour indicator
light will turn on, and display will show remaining hours
before air conditioner will turn on.
7. Press the plus or minus button to change delay time (1 to
24 hours).
8. Press TIMER again or wait 10 seconds. Timer indicator light
will remain on. Hour indicator light will turn off, and Room
indicator light will turn on. Display will show current room
temperature.
13