Weber Summit E-420 Owner's Manual page 28

LIGHTING THE ROTISSERIE BURNER
ROTISSERIE BURNER SNAP IGNITION
Note: Each control knob snap igniter creates a spark from the igniter electrode to the
burner lighting tube You generate the energy for the spark by pushing in the control
knob and turning to "START_HI "' This will ignite each individual burner
Ak ATTENTION: READ BEFORE
LIGHTING ROTISSERIE BURNER
After a period of non-use, before lighting the Rotisserie
Burner, a few seconds must pass for the gas supply line to
fill.
When using the snap igniter you will see a flash of flames
moving from left to right across the Rotisserie Burner
surface, the Rotisserie Burner is not lit until the entire
ceramic surface is aflame.
At this point, start a count of 20 seconds before releasing the
Rotisserie Burner control knob.
The Rotisserie Burner surface will glow red once the burner
is fully ignited.
*The grill illustrated may have
slight differences than the
model purchased.
Ak DANGER
Failure to open the lid while igniting the grill, or not waiting
5 minutes to allow the gas to clear if the grill does not light,
may result in an explosive flare-up which can cause serious
bodily injury or death.
Ak CAUTION: The Rotisserie Burner flame may be difficult to
see on a bright sunny day.
A_ WARNING: Check hose before each use of grill for nicks,
cracking, abrasions or cuts. If the hose is found to be
damaged in any way, do not use the grill. Replace using
only a Weber _ authorized replacement hose. Contact the
Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com _,
1) Open the lid.
2)
Remove the
warming
rackandthe
cooking grates
fromthecookbox.
3)
Makesureall burnercontrolknobsareturnedoff.
(Push
control k nobinandturn
clockwise to ensurethatit is inthe "OFF"
position.)
/k WARNING: The burner control knobs must be in the "OFF"
position before turning on the liquid propane cylinder tank
valve. If they are not in the "OFF" position, when you turn on
the LP cylinder valve, the "excess gas flow control" feature
will activate, limiting the flow of gas from the LP cylinder. If
this should occur, turn off the LP cylinder valve and burner
control knobs. Then start over.
DANGER
When the "excess gas flow control" feature is activated,
a small amount of gas is still flowing to the burners. After
turning off the cylinder and burner control knobs, wait at
least 5 minutes for the gas to clear before attempting to light
the grill. Failure to do so may result in an explosive flare-up,
which can cause serious bodily injury or death.
® ®
w w
4) Turn the cylinder on by turning the cylinder valve counter-clockwise.
/k WARNING: Do not lean over the open grill.
5) Push the control knob in and turn to "START/HI". This action will spark the
igniter and light the Rotisserie Burner. Continue to use the snap igniteruntil the
Rotisserie Burner has ignited.Release the control knob.
6) Check that the burner is lit by looking tor the rotisserie burner to glow red.
/k WARNING: If the rotisserie burner does not light, turn the
burner control knob to "OFF" and wait 5 minutes to let the
gas clear before you try again or try to light with a match.
Note: When usklg the rotisserte with the lid closed, only light two of the mak7 burners
on each side of the food (See Gdl/ing Methods-Indirect Cooking) Check your food
periodically to prevent over cOOking on the outside Turn off the rotisserie burner once
the food has browned to the desired color Finish cooking on indirect heat
TO EXTINGUISH
Push in and turn the rotisserie burner control knob clockwise to "OFF" position. Turn
gas supply off at the source.