Programming The Remote Control For Use With Your Audio/Video Devices; Device Code Setup - Toshiba 65HX83 Owner's Manual

Programming the remote control for use with
your audio/video devices
Device code setup
1. Refer to the multi-brand remote control device code table on
pages 22-23 to find the code for the brand of your device.
If more than one code is listed, try each one separately until you
find the one that works.
2. Press MODE until the Mode indicator for the device ((:ABLE/
SAT, VCR, DVD, AUDIO1, AUD102) lights up.
3. While holding down the RECALL button, press the Channel
Number buttons to enter the four-digit code for your brand of
device. If a valid code is entered, the mode indicator will blink
twice. If an invalid code is entered, the mode indicator will blink
one long blink.
4. Point the remote control at the device and press POWER to test
the code.
If the device turns on, you have entered the correct code.
lfthe device does not respond to the remote control, you may
have entered the wrong code. Repeat steps 3 and 4 using another
code.
Note: Inadd/dontoPOWER, c onllrmthatall necessary k eyson the TV
remotecontroloperate yourdevice ff somekeysarenot operational, repeat
thedevicecodesetupusinganothercode(/Tother c odesarelistedforyour
device) If,aftertrying all listedcodes,thenecessary k eysdo notoperate your
device, u sethedevice's odginal r emotecontrol
5. Press MODE to select the TV mode to control the TV.
Note:
• A/thoughyournew TV'sten?ore control
includes codesfor many devices,it may not
include codesfor some or all of the
features on certain devicesyou wish to
control ff you are unable to program the
TV'sremote control to operate your device
or some of the features on that device, use
the device's remote contrb/ or the contrb/s
on ffTedewce
• Everytime you change the batteriesyou
wfflneed to reprogram the remote conu_L
• Some newer VCRsrespond to either of two
codes TheseVCRshave a switch labeled
"VCRI/VCR2" Ifyour VCRhas this kind of
switch and does not respond to the codes
fur your VCRbrand, set the switch to the
other pus/don ("VCR 7" or "VCR2'? and
reprogram the remote conubL
Searching and sampling the code of a device (8500)
lfyou do not know the device code for a particular device, you can
cycle the remote control through the available codes for that device
mode and sample the functions to find the code that operates the
target device. The keys available to be sampled, provided they are
applicable to that mode, are POWER, 1, VOL A, CH A, and PLAY.
Invalid keys will be ignored while in program mode.
To cycle through each available device code and sample its functions:
1. Press MODE to select the mode you want to set up.
2. While holding down the RECALL button, press 8 -5 -0 -0.
The remote control will enter program mode.
3. Point the remote control at the target device and press POWER
(or other function buttons that are available to be sampled).
4. lfthe device responds to the remote control:
Press RECALL to store the device code.
The mode indicator will blink twice and the remote control
will exit the program mode.
If tile device does not respond to tile remote control:
Press A, and then press POWER.
Repeat this step until the device responds to the remote
control, and then press RECALL.
Note: When a search cycleis completed, the mode/n&cator will
blink three times Theremote control wdl begin to cycle through the
availablecodes again ff no key is pressed within 70 seconds whfte
programming the remote control wdl exit the program mode and
retum to the previouscode
20