Cd/Deck Synchro Recording - Pioneer CT-W603RS Operating Instructions Manual

To stop recording temporarily
Press the pause (11) button on either deck (both decks pause).
• To resume recording, press the pause (Ill button again.
To stop recording
Press the stop ( • ) button on either deck (both decks stop).
NO TES:
• When either tape reaches the end, parallelrecording is complet-
ed. Therefore, use the same length tapes for both decks.
• If the erasure prevention tabs are broken, you cannot parallel-
record even if you press PARALLEL REC button.
• Always start recording from the forward direction (FWD) for both
sides recording. Otherwise, the tape automatically stops when
it reaches the end in the reverse direction.
• Since the recording level adjustment affects both decks equal-
ly, it is recommended that the same type of cassette tapes be
used.
• If you press the recording mute ( 0 ) button, both decks enter
the recording mute mode (see page 14).
CDeDECK SYNCHRO RECORDING
7 2
4 8
RECORDING
If the CD player has a program function to determine the order of
playback, program the CD player before beginning this operation.
1. Load a compact disc in the CD player.
2. Load the cassette for recording.
• Rewind the tape to the desired starting position.
3. Set the REV MODE switch.
• To record on one side only, set the switch to the _ posi-
tion. To record on both sides, set the switch to the _ posi-
tion.
4. Set the DOLBY NR ON/OFF switch and set the DOLBY
NR switch.
5, Press the play button of the CD player.
6. Adjust the recording level.
• See page 14.
7. Press the stop (11) button of both the cassette deck
and the CD player.
• Unless both this deck and the CD player are in stop mode,
synchro recording cannot be performed.
8. Press the CD SYNC button,
• The cassette deck begins recording, and the CD player be-
gins playback.
ABOUT RECORDING
You can use either DECK I or II for synchro recording (CT-W803RS/
CT-W703RS)
You can use the Deck II for synchro recording .(CT-W603RS only).
You can also operate relay recording with the CD player (CT-
W803RS/CT-W703RS).
When the compact disc finishes playing:
The CD player enters stop mode and the cassette deck enters
recording standby mode. Change the disc and press the play but-
ton of the CD player to resume recording. If the CD player does
not resume play within one minute, the cassette deck enters stop
mode.
When the CD player changes discs
(twin tray or multi-play disc CD players):
The cassette deck enters recording standby mode, and resumes
recording when the CD player begins playing the next disc. A four-
second blank space is automatically created between tracks.
When the end of the tape is reached while the CD
player is still playing:
The CD player returns to the beginning of the currentlyplaying se-
lection and then enters the pause mode. To resume recording,
load another tape and check the tape running indicator to ensure
that the tape is moving in the desired direction. If not, press the
playback (b, or <1) button to change the tape direction, then im-
mediately press the stop (11) button. The tape running indicator
will change direction. Synchro recording can be resumed by
pressing the CD SYNC button again. (The CD SYNC button should
be pressed within 1 minute. If more than 1 minute elapses, the CD
player will enter stop mode.)
If the auto-reverse function operates while the CD is
still playing:
The CD player returns to the beginning of the current selection and
enters pause mode.
A ten-second blank space is automatically created on the reverse
side, then the CD player resumes playback and the deck resumes
recording.
[CT-W803RS/CT-W703RS only.]
• Relay recording (set the REV MODE switch to c-_--_ (RELAY/
SK)P).)
• After DECK I stops, DECK II starts to record.
• If the CD player stops playback while DECK I is recording, DECK
I stops and DECK II starts recording from the beginning of the
CD (if the CD player is either a twin or multi CD player, DECK
II will record the next CD).
NO TE:
During rela/y recording, DECK I stops when CDs are changed as
well as when the tape in DECK I reaches the end, and DECK II starts
recording.
• A twin CD player stands for a twin-tray compact disc player.
• A multi CD player stands for a magazine compact disc player
(sequential playback of 6 compact-disc player).
NO TES:
• The CDoDECK SYNCHRO function only works with PIONEER
CD players equipped with the CDoDECK SYNCHRO function.
• Be sure to connect the deck and the CD player with the
CDoDECK SYNCHRO control cord.
• Although recording begins when the CD S YNC buton is
pressed, the CD player does not start playback until the button
is released. This function can be used to advance the tape past
the leader section, or to create a blank section on the tape.
• Only PIONEER CD players equipped with a CDeDECK SYNCHRO
jack can be used for CDoDECK SYNCHRO recording. Any type
of CD player which meets these requirements, including twin-
tray or multiplay models, can be used.
17
<RRB1143>
En