Table of Contents
Advertisement
Connections
Setup
TV + HDTV Tuner + VCR + DVD Player
1.
Make sure cable or antenna
and/or
satellite
is connected
to your VCR.
A. Connect the coaxial cable frol_q your cable outlet or antenna to the antenna
input on tile HDTV Tuner.
B. Connect the satellite dish antenna
to the satellite input on the HDTV Tuner.
2.
Make the video connection
between
your HDTV Tuner
and the TV.
A. Best Conneclion:
DVI-HDTV
Connect a DVI-HDTV cable to the DVI-HDTV iack on the back of your HDTV Tuner. Connect the other end of the
cable to the DVI-HDTV input on the back of "IV.
- OR -
B. Very Good Connection:
Connect three video grade cables to the CMP1 Y PB PR jacks on the back of the TV and to
|he Y PB PR jacks on the HDTV Tuner.
Notes: The DVI-HDTV and Y PB PRjacks send the digital cable signal to the TV in digital and analog formats,
respectively.
3.
Make the audio connection
between
your HDTV Tuner
and the TV (to match
your video connection).
A. If you used the DVI-HDTV jack:
Connect the audio (white and red) cables to the DVI-HDTV L and R audio jacks on the back of the TV and to the
Audio Output jacks on the HDTV Tuner.
- OR -
B. If you used the Component
Video jacks:
Connect the audio (white and red) cables to the CMP1 L and R audio jacks on the back of the TV and to the Audio
Output jacks on tile HDTV Tunei:
4.
Connect
your HDTV Tuner
to your VCR.
A. Connect a coaxial cable to the HDTV Tuner's antenna
output and to VCR's antenna input.
B. Connect the audio (white and red) cables to the Audio Output jacks on the HDTV Tuner and to the Audio Input
jacks on the VCR.
C. Connect the video cable to the Video Output jack on the HDTV Tuner and to the Video Input iack on the VCR.
5.
Connect
your VCR to your TV.
A. Connect a coaxial cable to the VCR's antenna
output and to the ANTENNA/CABLE Input iack on tile TV.
B. Connect the audio (whim and red) cables to the VID2 L/MONO and R audio jacks on the back of the TV and to the
Audio Output iacks on the VCR.
C. Connect the video cable to the VID2 V (video) jack on the back of the "IV and to the Video Output jack on the VCR.
6.
Connect
your DVD player
to your TV.
A. Connect tile audio (white and red) cables to the CMP2 L and R audio iacks on the back of the "IV and to the Audio
Output jacks on the DVD player.
B. Connect three video grade cables to the CMP2 Y PB PR iacks on the back of the "IV and to the Y PB PR jacks on the
DVD player.
Notes: If your DVD player doesn't have Y PBPRjacks, but does have an S-Video jack, connect the player to the TV's
VID1 S-VIDEOjack using an S-Video cable.
If your DVD player doesn't have an S-Video jack, connect the player to the TV's VID1 V (video)jack using a video
cable.
Important: If you use the TV's VID1 S-VIDEOor V (video)jack to connect the DVD player, you must connect the
audio cables to the TV's VID1 L/MONO and Rjacks.
Go to page
15
Chapter
1
Graphics contained
within this publication
ar_ fi_r r_presentation
only.
7
Advertisement
Table of Contents
