LG 22LG3DCH Owner's Manual page 105

COMMERCIAL MODE SETUP
N
0
I'rl
N
0
I-I-I
I-I-I
-t
c
Detailed Descriptions of Installer Menu Items
011 - KEY DEFEAT (Keyboard Defeat)
If set to 1, key defeat prevents the end user from
accessing the on-screen menus with the TV front
panel--MENU, SELECT, and Left / Right arrow keys do
not function. If set to 0, those keys do function.
NOTE: The menus can always be accessed by press-
ing MENU on the remote.
012 - IR BANKS EN (IR Banks Enable)
For direct access to a particular Channel Bank. When
enabled, installer can access a channel bank by
inputting the IR code for the bank.
013 - SCAN MODE (Functional after 2-S-
S+Menu setup transfer)
Allows variation in setting the TV On/Off with Channel
UP/DOWN. You may opt for TV channels only; TV
channels + Off/ON; with these settings for Scan Mode:
SCAN MODE Characteristics
0 Channel up/down keyschange channels only.
1 Channel down below the lowest channel
(or channel up higher than the highest)
and TV turns off.
014 - STRT CH IN SM
(Start Channel in Scan Mode) If set to 1, installs TV
On/Off event below the start channel at TV turn On. If
set to 1, the user can select channels with either
Channel Up/Down or by direct keypad entry. If set to
0, only those channels that are entered for scanning
can be selected.
01S - SLEEP TIMER
If set to 1, the SLEEP TIMER feature may be used. If
set to 0, the Sleep Timer is not available.
01 6 - EN TIMER (Enable On/Off Timers)
If set to 1, Timer function is available to end user and
enabled continuously. Set to 0 to disable On/Off
Timers. (Clock must be set in order to use Timers.)
017 - ALARM *
Gives the installer the option of making the Alarm
function available to the end user. If set to 1, Alarm
function is available to end user. Set to 0 to disable the
Alarm function.
NOTE: Clock must be set before the Alarm function
will work.
020 - FEATURE LEVEL
Installer should leave item 20 FEATURE LEVEL
set to 1 (default).
_ efault set to ZEN 1 for Zenith IR codes
remote control operation. Set O, P LBL for
Zenith Private Label IR remote control opera-
tion.
Warning: Do not set to "0" or remote will not control
TV.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control); have it
available to end user to filter and control or otherwise
restrict programming content that can appear. Set to 0
to turn V-Chip feature Off, not available to end user;
no programming restrictions can be set.
* Only affects Function Menu if enabled by
some PPV providers.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip
(Parental Control) block hours. Default setting is for 12
blocking hours.
023 - CAPTION LOCK
Set to 1 to restore previous caption On/Off state after
turn Off. If set to O, captions are always Off at turn
On.
02S - FUNCTION PRE (Function Preview)
Set to 0 to suppress CHANNEL PREVIEW from the
FUNCTION menu with some Pay-Per-View systems.
027 - HOSPITAL MODE
The default is 2 (which favors most hospitals). With
this setting two things are affected: Channel Banks 1,2
and 3 are accessible, while Bank 4 can be made inac-
tive by removing all the channels from Channel Bank 4.
Then, if Channel Bank 4 is selected when the TV is
turned on, the TV screen will show "Inactive TV". The
Channel Bank 4 setup allows the hospital to present
TV viewing options to the patient. The patient can
select programming options available in either Bank 1,
2 or 3. Channel Banks are available in all hospital
modes 1 an 2.
• The IR code that will control the TV depends on Item
20-1 Feature Level setting.
Hosp. Mode = 0 Hospital Mode disabled.
Hosp. Mode = 1 Zenith RE IR Code (Bed 1)
Hosp. Mode = 2 Zenith IR Code (Bed 2)
028 - CH. OVERIDE (Channel Override)
If set to 1, the user can select channels with either
Channel Up/Down or by direct number keypad entry. If
set to 0, only those channels that are active in the TVs
memory can be selected.
029 - OLD OCV (On Command Video
TM)
Set to 1 for operation with systems from On Command
Corporation.
(Continued on next page)
104