LG 22LG3DCH Owner's Manual page 104

Detai[ed Descriptions of Insta[[er Menu Items
000 - INSTALLER SEQUENCE
Specifies entry sequence to the InstallerMenu.
0 = 9876 1 = 4321
2 = 1478 3 = 3698
001 - POWER MANAGE (Power Management)
Determines hours of no activity before automatic shutoff.
The POWER MANAGE function is for saving energy. If set
to 0, Power Manage is Off. SeRings range from 0 Z with I
7 representing the hours that the unit will remain On,
unless there has been activity from either the control panel
or remote control.
002 - AC ON (AC Power Switchable)
If set to I, allows the TV to turn On just by applying AC
power. Pressing the On button is not necessary. This is
desirable if the TV is plugged into a cable box or a power
outlet controlled by a wall switch. Use ADJ Left/Right arrow
to choose 0 or I where 0 is the default is Off, and I is On.
NOTE: If set to I (On), the TV does not respond to
On/Off commands from either the remote or the display
control panel, and the SLEEPTIMER is also nonfunctional.
003 - BAND/AFC (Band/Automatic Frequency
Control)
There are 4 possible settings for this option:
0 = Broadcast 1 = CATV
2 = HRC 3 = IRC
If some channels were not found by Auto Tuning (Channel
Search), select the appropriate Band setting here and add
the channels using the Channel Edit option in the Channel
Menu.
004 - STRT CHANNEL (Start Channel)
If active, this function allows you to determine the initial
channel number when the TV is turned On. This feature is
useful for an in-house information channel, since the TV
would always select that channel when it is turned On.
Setting this to 255 causes the last channel viewed when the
TV was turned Off, to be the tuned to channel when the
TV is turned On again. Note: For a digital Start Channel,
always remember to set item 104 to the Minor Start
Channel number.
255 = Last channel
126 Map to Channel 3.
1 ~ 125 = Ch X 0 = Aux
127 Map to Channel 4.
OOS - CHAN LOCK (Channel Lock)
CHAN LOCK is ideal if the system must always be on the
same channel. Changing channels with Channel Up/Down
or keypad numbers is impossible. Channel Lock is inactive if
set to 0 (default).
Generally, this feature is used in connection with START
CHANNEL (Installer item 004) where the start channel
may, for example, be set to 3 or 4. If the start channel is 3,
then the TV will remain locked on Channel 3.
NOTE: For Items 007, 008 and 009
For legacy reasons, the scale used is 0 - 63. The PTC soft-
ware will translate this to the 0 - 100 scale used by the TV.
To translate a TV volume level to the installer menu value,
use the following formula:
Installer Value = TV Value x 63
100
Enter only the whole number (disregard fractions).
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial vol-
ume level setting when the TV is turned On. This feature is
useful for an in-house information channel, since the TV
would always select that volume level when it is turned On.
The range of values are 0 - 63,255. If255 is selected, the
current volume level will be retained in memory when the
TV is turned Off;, at turn On, the volume level will be auto-
matically set at the previous or last level.
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allow-
able with the VOLUME (VOL) Up/Down control. In this
way, for example, someone cannot set the volume too low
to hear. The value range is from 0 to 63 -- change values
with ADJ LeffJRight arrow. The factory default is 0, which
provides the full range of volume control, if item 009 MAX
VOLUME is also set to 63. It may be best to set the same
value on every TV.
NOTE: The minimum volume level cannot have a value set-
ting higher than the MAX VOLUME level (described
below).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allow-
able with the VOLUME (VOL) Up/Down controls. In this
way, for example, someone can not set the volume level
high enough to disturb others. The value range is 0 to 63,
with 63 as the default, which gives the user the full range of
volume control, if item 008 MIN VOLUME is also set at 0.
Change values with ADJ Left/Right arrow keys. It may be
best to set the same value on every TV.
NOTE: The maximum volume level cannot have a value
setting lower than the MIN VOLUME level (described previ-
ously).
01 0 - MUTE DISABLE
Enablesor disables sound mute function. If set to 1, sound
cannot be muted. If set to 0, sound can be muted.
(Continued on next page)
N
0
I'rl
N
0
I-I-I
I-I-I
-t
c
103