Table Of Contents - Extron electronics IPL T SF24 Series User Manual

Quick Start Guide - IPL T SF24, IPL T SFI244,
cont'd
Step 4
Attach the serial communication cables from the IPL T unit to the
devices being controlled.
Step 5
Connect power cords and turn on the equipment in the following
order: output devices (projectors, monitors, speakers), the IPL T
interface, the serial controller or computer (PC), then all input
devices (DSS, cable boxes, etc.).
Step 6
Configure the IPL T interface using the ARP command. Refer to
IPL T interface configuration in chapter 3 for more information.
Step 7
Communicate with the IPL T interface via the default Web pages.
Refer to Communication with the interface in chapter 4 for more
information.
Motion Detector
RS-232
Extron
IPL T SFI244
Ethernet Control
Interface
IR
3
I/ O 2
E X
F L 1
S
G
x 4 S
x -x 3
x -x 2 G
1 S
6 -x G
-A M 2 S
-0 5 CO
0 0 M 1
L A N CO
RX
W E R TX
P O RX
X TX
12 V M A
.5 A
TCP/IP
RS-232
Network
Ethernet
Remote User
Control &
Extron
Administrator
MLS 103 SV
Monitoring
S-video & Audio
Switcher
Typical connection setup (IPL T SFI244 shown)
QS-2 IPL T SF24 and IPL T SFI244 • Quick Start Guide
Projector
Screen
Y 4
LA
RE
Y 3
LA Control
RE
Y 2 C NC
LA
RE NO
Y 1 C NC
LA
RE NO
Extron C NC
NO
C NC
NO
IPL T RLY4
Relay Box
4
G
Lighting System
VCR/
DVD 2
Extron
DVD 1
IR Emitters
DSS Receiver

Table of Contents

Chapter 1 • Introduction
About this Manual
................................................................ 1-2
About the IPL T SF24 and SFI244 Interfaces
Features
...................................................................................... 1-3
Chapter 2 • Installation and Operation
Installation Overview
Mounting the IPL T Interface
Rack mounting ....................................................................... 2-2
Furniture or projector mounting .......................................... 2-4
Rear Panel Features and Cabling
Power ..................................................................................... 2-5
Ethernet/LAN ......................................................................... 2-6
Serial communication ............................................................ 2-7
Identification ......................................................................... 2-8
Operation
................................................................................... 2-8
Front panel indicators ........................................................... 2-9
Resetting the unit ................................................................ 2-10
Chapter 3 • Connection and Configuration
Connecting the Hardware
Ethernet connection .............................................................. 3-2
Serial connection ................................................................... 3-3
IR connection (SFI244 only) ................................................... 3-3
Flex I/O connection ................................................................ 3-4
Configuring the Hardware
PC configuration .................................................................... 3-5
Initial start up ........................................................................
IPL T interface configuration ................................................ 3-5
Configuring the IPL T interface using the ARP command .
Configuring the IPL T interface using direct PC connection
Firmware upgrades ................................................................ 3-8
Chapter 4 • Communication and Control
Ports Overview
........................................................................ 4-2
Flex I/O ports .......................................................................... 4-2
Digital input ..........................................................................
Digital output ........................................................................
Analog input .........................................................................
Bidirectional serial control interface ports .......................... 4-5
IPL T SF24 and IPL T SFI244 • Table of Contents
.......................................................... 1-1
............. 1-2
........................ 2-1
.......................................................... 2-2
........................................... 2-2
................................... 2-5
............... 3-1
................................................. 3-2
................................................ 3-5
.................... 4-1
3-5
3-5
3-7
4-3
4-4
4-5
iii