Table of Contents
Advertisement
VCR Plus+ Setup (continued)
*Important:
If the remote control POWER, ACTION, PROG, CH_idY, INDEX or ADD/DLT button does not
work when pressed, press the VCR button on the remote and try the button again.
In order for the VCR to read the VCR Plus+ code, some set up is required. A Guide (VCR Plus+) channel number
is assigned to each local broadcast and cable station. Because this number sometimes differs from the channel
your TV receives the station on, it is necessary to program the VCR with local channel information.
!
3.
5
]
4
Channel
Setup Preparations
NOTE: Complete the steps on this page if your
cable box can be controlled with the VCR, or
your VCR hook-up resembles "B" on page 30.
Prepare a list like the example below.
Thislistwill helpyousmoothlyenterthe information
needed in step =4"at right.
You will need the following to complete the list:
• A line up of normaland/orcablestationsyou
receivealongwiththe channelnumbersyour"IV
receivesthem on. A cablechannelline-upchart
is supplied by yourcablecompany.
•
A listof Guide (VCR Plus+)channelnumbers
assigned to the stationsyoureceive.Thislistis
availablein TV Guideand the TV listings found
in selectednewspapers.
1
Make.a chart with 3 columns like the example
below. In the left column, fill in the name or call
letters of the stations you receive.
2
In the middle column, fill in each station's
assigned Guide (VCR Plus+) number found in
TV Guide, newspapers,
etc.
3
In the right column, fill in the channel number
that your TV receives the s.tab'on on from y_ur
channel line-up.
Broadcast or
Cable
Station Name
HBO
Ni(_kelodeon
EXAMPLE ONLY
Assigned
Guide
(VCR Plus+)
channel no.
33
38
04
11
Channel
no. your TV
receives the
station on
15
2O
04
32
VCR Plus+ Channel
Setup ,
complete
this page only if Type B
connection
method (pg.30) is used.
• Before you begin, complete the Channel Setup
Preparations below left.
Important Note:
If your VCR connection type changes from type A to B,
repeat steps 1-4 of page 31 and select VCR • CABLE/
DSS BOX • TV or VCR • TV before proceeding with
these steps.
1
Press ACTION* to display
the menu.
2
Press AV to select "SET UP
CHANNEL," and then press
MENU
.........
SET UP VCR
SET UP FEATURE
_ENGL
I SH
SELECT:& •
KEY
:ACTION KEY
• to display the "SET UP CHANNEL" screen.
3
Press AY to select "VCR
Plus+ CH SET UP," and then
press • to display the "VCR
Plus+ CH SET UP" screen.
I ....
SET UP CHANNEL ....
]
IANTENNA : CABLE
I
I_ro sET
I
IO_V_INEL CAPT I ON
/
I
SELECT:&
•
KEY
I
|
SET
:i_
KEY
|
END
:ACTION
KEY
J
IMPORTANT NOTE:
For step "4," use the list you prepared. You may leave
lines blank if you don't receive that station, or if the
GUIDE CH number and the CABLE (or TV) CH numbers
are the same.
VCR Plus+ CH SET UP
4
Press • to move the shaded
area to the right side.
Then, press AV to change
CABLE or TV CH number.
Next, press < to set the number.
Now, press AV to continue.
Repeatthis operation untilthe list
iscomplete.
GUIDIE
CH
CABLE
CH
• m
""
02
--
SELECT:•
•
KEY
SET
:_
KEY
END
:ACTION
KEY
I
VCR
Plus+
CH
SET
UP
GUIDE
CH
CABLE
CH
• 01
[]
02
--
,
S_LECT:&
•
KEY
SET
:<
KEY
END
:ACTION
KEY
To Enter More Programs
Press AY and b" to select the incorrect CABLE or TV CH
number. Then, press AY to change, or ADD/DLT to delete
the channel.
5
Press ACTION
three times to exit
the VCR Plus+ CH SET UP mode.
Advertisement
Table of Contents
